AVer FB2026 Скачать руководство пользователя страница 70

Страница: 70 / 78

Output Setting:

Mode setting:

OnOff Switch:

Relay status is based on sensor triggered times.

Time Switch:

To restore the original relay status after the interval time.

[Note]

GPIO pin define please refer to the part of Front / Back plane & I/O port pin assignment.

Ground (G)

ALARM INPUT:

Normal: 5V (The voltage differential from ALM_IN pin & Ground)

Active: 0V (Short the pin of ALM_IN and Ground pin)

RELAY OUTPUT:

MAX: 50 mA, DV 5V

Ground(G)

Status Information

Click

Apply

button to save the configuration.



Networking Info:

Displays network information of the IP camera.



Product Info:

Server Name:

Assigns a name to the IP camera and the name shows on the IP Installer. Also,

displays the related information of the IP camera. Mark

Status Bar

to display the Server Name of

IP camera on preview interface.

LED indicator:

To disable or enable the LED indicator on the IP camera.

Содержание FB2026















































































Результаты поиска

Содержание FB2026

Отзывы:

Похожие инструкции для FB2026

Бренды по названию

Популярные бренды

AVer FB2026, Руководство пользователя

Результаты поиска

Содержание FB2026

Отзывы:

Похожие инструкции для FB2026

Бренды по названию

Популярные бренды