AVer FB2026 Скачать руководство пользователя страница 27

Страница: 27 / 78

System > General

n this section, only admins are authorized to configure the IP camera system maintenance and the

date and time settings.

System > General > Maintenance

In the Maintenance tab, the administrator can check the system event log, upgrade the system

firmware, reset the configuration settings without having to change the user management and network

settings, reboot, and restore all back to factory default settings.

(1)
(2)

(3)

(4)

(5)

(6)

Name

Function

(1) Export Settings

Upload to save all the configuration settings from the IP camera to

the computer hard disk.

(2) Reboot

Turn the IP camera off and on again.

(3) Factory default

Set all the configuration settings back to default except the user

management and network settings.

Содержание FB2026















































































Результаты поиска

Содержание FB2026

Отзывы:

Похожие инструкции для FB2026

Бренды по названию

Популярные бренды

AVer FB2026, Руководство пользователя

Результаты поиска

Содержание FB2026

Отзывы:

Похожие инструкции для FB2026

Бренды по названию

Популярные бренды