background image

4

1

Do not use outside the design intent.

2

Do not use equipment with this tool/machine other than that recommended and supplied by Avdel UK Limited. 

3

Any modification undertaken by the customer to the tool/machine, nose assemblies, accessories or any equipment supplied by

Avdel UK Limited or their representatives, shall be the customer’s entire responsibility. Avdel UK Limited will be pl eased to

advise upon any proposed modification.

4

The tool/machine must be maintained in a safe working condition at all times and examined at regular intervals for damage and function

by trained competent personnel. Any dismantling procedure shall be undertaken only by personnel trained in Avdel UK Limited 

procedures. Do not dismantle this tool/machine without prior reference to the maintenance instructions. Please contact Avdel UK Limited

with your training requirements.

5

The tool/machine shall at all times be operated in accordance with relevant Health and Safety legislation. In the U.K. the “Health and

Safety at Work etc. Act 1974” applies. Any question regarding the correct operation of the tool/machine and operator safety should be

directed to Avdel UK Limited.

6

The precautions to be observed when using this tool/machine must be explained by the customer to all operators.

7

Always disconnect the airline from the tool/machine inlet before attempting to adjust, fit or remove a nose assembly.

8

Do not operate a tool/machine that is directed towards any person(s) or the operator.

9

Always adopt a firm footing or a stable position before operating the tool/machine.

10

Ensure that vent holes do not become blocked or covered and that the hoses are always in good condition.

11

The operating pressure shall not exceed 6.5 bar (95 lbf/in

2

).

12

Do not operate the tool without full nose equipment in place.

13

Care shall be taken to ensure that spent stems are not allowed to create a hazard.

14

07200 tools must be fitted with an undamaged pintail deflector before operating.

15

Avoid holding the head of the tool during initial connection as it may move and could cause injury.

16

When using the tool, the wearing of safety glasses is required both by the operator and others in the vicinity to protect against pin

ejection, should a fastener be placed ‘in air’. We recommend  wearing gloves if there are sharp edges or corners on the application.

17

Take care to avoid entanglement of loose clothes, ties, long hair, cleaning rags etc. in the moving parts of the tool which should be kept

dry and clean for best possible grip.

18

When carrying the tool from place to place keep hands away from the trigger/lever to avoid inadvertent start up.

19

Ensure the plug filling the circlip removal aperture is in place at all times.

This instruction manual must be read with particular attention to the following safety rules, by any person

installing, operating, or servicing this tool.

Safety Rules

Содержание 07200




















Отзывы: