manualshive.com logo in svg

Avaya J100 Series, Установка и администрирование, Страница: 280 / 528

Поделиться
Скачать
Avaya J100 Series Скачать руководство пользователя страница 280

Parameter name

Default value

Recommended settings

REGISTERWAIT

900

This parameter represents
number of seconds between
register refreshes. It is
recommended to set the value to
“120” to “180” seconds.

This enables faster recovery
detection of signaling servers.

Related links

Redundancy in a Broadsoft environment

 on page 278

Redundancy in a Netsapiens environment

In a Netsapiens environment, you can use up to six SIP controllers in a redundancy deployment.
You can use UDP, TCP, or TLS to connect to the SIP controllers.

For more information on the Netsapiens redundancy deployment, see Netsapiens documentation
at 

HTTPS://NETSAPIENS.COM/

.

Related links

SIP server redundancy

 on page 276

Redundancy parameters - Netsapiens

 on page 280

Redundancy parameters - Netsapiens

To configure the phone for redundant signaling mode in a Netsapiens environment use

46xxsettings.txt

 file to set the following parameters:

Parameter name

Default value

Required settings

SIPREGPROXYPOLICY

simultaneous

This must be set to the value
alternate.

SIP_CONTROLLERS_LIST_2

Null

This parameter should not be set
and left at default.

Open SIP redundancy does not
support IPv6.

3PCC_SERVER_MODE

0

This parameter should be set to
3.

Table continues…

SIP server redundancy configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

280

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов