manualshive.com logo in svg

Avaya J100 Series, Установка и администрирование, Страница: 276 / 528

Поделиться
Скачать
Avaya J100 Series Скачать руководство пользователя страница 276

Chapter 10: SIP server redundancy

configuration

SIP server redundancy

In an Open SIP environment, you can configure Avaya J100 Series IP Phones to connect to one
of the following SIP servers in a redundant mode.

• Generic open SIP - redundant mode is not supported. However, by connecting to one of the

recommended Open SIP servers, you can configure the phone for redundant signaling mode.

• BroadSoft

• Netsapiens

When in redundant mode, the phone uses signaling service from a secondary server if the primary
server is down. The following sections explain how to administer a phone for a redundant
connection in different modes.

Related links

Redundancy in generic Open SIP

 on page 276

Redundancy in a Broadsoft environment

 on page 278

Redundancy in a Netsapiens environment

 on page 280

Redundancy in generic Open SIP

In a generic Open SIP environment, phone connects to the recommended Open SIP server.

Related links

SIP server redundancy

 on page 276

Redundancy parameters - generic Open SIP

 on page 276

Redundancy parameters - generic Open SIP

To configure the phone for redundant signaling mode in a generic Open SIP environment, use the

46xxsettings.txt

 file to set the following parameters:

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

276

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов