background image

10 

 

CARE AND MAINTENANCE 

 

Caution 

Failure to unplug the ice maker could result in electrical shock or personal injury. 

 

 

Cleaning Your Ice Maker 

 

To ensure the cleanliness of the ice cubes, water in the reservoir should be replaced every 24 
hours.  

 

Remove the drain plug to drain remaining water from the water reservoir when the ice maker will 
not be used for long period of time. Screw the drain plug back in place after the water has been 
drained.  

 

Always change with fresh water before starting ice production at initial installation or after long 
shut-off periods.  

 

Please clean your Ice maker regularly. When cleaning, unplug the unit and remove the ice 
cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of 
the Ice maker. Do not spray Ice maker with chemicals or diluted agents such as acids, gasoline 
or oil. Rinse thoroughly before starting.  

 

 

Space Requirements   

 

During transportation, the incline angle of the cabinet should not be over 45°  

 

Do not turn the Ice maker upside down. Problems could occur in the compressor and sealed 
system.  

 

The Ice maker should be placed horizontally on a properly leveled surface.  

 

To ensure proper ventilation for your Ice maker allow 6” of space at the top, the back and on 
each side.  

 

Before using the Ice maker for the first time, please wait 2 hours after positioning it.  

 

Clean the inner liner, ice-bin, water box, water cup frequently.  

 

IMPORTANT: Do not install the Ice maker near an oven, radiator, or other heat source.  

 

 

Power Failure 

Most power failures are corrected within a few hours and should not affect the temperature of your 
ice maker if you minimize the number of times the ice-bin is opened. If the power is going to be OFF 
for a longer period of time, you need to take the proper steps to disconnect your appliance. 

 

Содержание IM12C-IS

































Отзывы: