manualshive.com logo in svg

AVANT 500 Series, Руководство оператора, Страница: 32 / 40

Поделиться
Скачать
AVANT 500 Series Скачать руководство пользователя страница 32

32

500 Series

12-14 Adjust and change the slide pads 
on telescopic boom

The telescopic boom is equipped with replaceable slide 
pads. At the lower end of the outer boom there are 
nylon slide pads. 1, 2, 3 and 4. In addition, there are four 
aluminium-bronze alloy slide pads (nos. 5,6,7 and 8), at 
the upper end of the inner boom. All slide pads can be 
replaced, and the nylon slide pads on the outer boom can 
also be adjusted. This way the natural wear of the slide 
pads, caused by the use of the telescopic boom, can be 
compensated.

Slide pads 1 to 4

 can be adjusted 

by mounting thin adjustment 
sheets between the boom and the 
slide pad. Extend the telescope 
almost completely and press 
the boom against the ground, it 
is the easiest way to mount the 
adjustment sheet under slide 
pad no. 2 . However, if there is 
substantial wear in the slide pads 
it is advisable to replace both pad 
no. 1 and 2.

Slide pads 5 to 8

 at the upper 

end of the inner boom last very 
long in normal use. Slide pads 5, 
6, 7 and 8 should be checked after 
every 400 operating hours and 
replaced at least after 800 hours. 
Checking is made by taking the 
inner boom completely out of 
the outer boom. If the pads have 
worn so much that they are in 
level with the boom, or excessive 
boom play can’t be removed by 
adjusting slide pads 1 to 4, replace 
all slide pads.

Part nos. for the slide pads are:
Slide pad 1 and 2: A48339
Slide pad 3 and 4: A48340
Slide pad 5 and 6: A47922
Slide pad 7 and 8: A48343
Washer under slide pads 5 and 6: A47941
Adjustment sheet, short: A48013 
Adjustment sheet, long: A48014  
 

15.-16. Clean air filter element

1.  Squeeze the rubber vent 

on the filter housing cover 
to drain water and dirt 
from the filter.

2.  Wipe the outer surface of 

the air filter housing clean 
before opening the filter.

3.  Remove the filter 

cartridge

4.  To clean the filter, tap the closed end of the filter 

gently against a flat, clean surface. Never use 
compressed air to clean the filter!

5.  Do not remove the inner element.
6.  Clean the inner components of the filter housing with 

a damp cloth

7.  Reinstall cartridge, ensure proper tightness and sealing 

of the filter and the housing cover.

2

1

3

4

5

6

7

8

Service and maintenance instructions

Содержание 500 Series









































Отзывы:

Нет отзывов