Autronica BX-10M1 Скачать руководство пользователя страница 29

Страница: 29 / 37

Appendix

Operator's Handbook, Fire Alarm Control panel BX-10M1, P-BX10M1/FE Rev. A, 050128, Autronica Fire and Security AS

Page 27

10.1.4 Fault/disabling/testing - alarm outputs

Fault/Disabling/Test

Yellow indicator with 3 functions: fault, disabling or testing of alarm outputs.

Error status

Disabling status

Test mode

Activated by break or short-
circuit in alarm outputs
(AK1 and AK2) FAD's.

•

Flashing yellow light
with fault – remains
active until the control
panel is reset.

Disabling indication has
priority over error or test.

•

Constant yellow light as
long as alarm output is
disabled.

•

Not implemented

10.1.5 Error/disabling/testing - general alarm output (BMA)

Fault/Disabling/Test

Yellow indicator with 3 functions: fault, disabling or testing of alarm transfer.

Error status

Disabling status

Test mode

Monitoring of errors/faults
in general alarm outputs.

•

Activated by break or
short circuit in BMA or
fuse F3.

•

Flashing yellow light –
remains active until the
control panel is reset.

Disabling function is activated
in operator mode by pressing
key 7.

•

Constant yellow light as
long as the outputs are
disabled.

•

Not implemented

10.1.6 Error/disabling/testing - general fault output (BMF)

Fault/Disabling/Test

Yellow indicator with 3 functions: fault, disabling or testing of alarm transfer.

Error status

Disabling status

Test mode

Monitoring of errors/faults
in general fault outputs.

•

Activated by break or
short circuit in BMF.

•

Flashing yellow light –
remains active until the
control panel is reset.

Disabling function is activated
in operator mode by pressing
key 8.

•

Constant yellow light as
long as the outputs are
disabled.

•

Not implemented

10.1.7 Immediate warning disabled

Fault/Disabling/Test

Immediate warning disabled

Yellow indicator is activated when the panel is configured for delayed alarm on the
alarm outputs (AK) and common alarm output (BMA) (appendix 10.2).

•

Constant yellow light is activated by configuration of a delayed alarm via operator
code and key-code, or via an auxiliary switch.

10.1.8 Fault in battery or battery fuse (F9)

Fault

Battery

•

Not in use for BX-10M1.

Содержание BX-10M1






































Результаты поиска

Содержание BX-10M1

Отзывы:

Похожие инструкции для BX-10M1

Бренды по названию

Популярные бренды

Autronica BX-10M1, Руководство оператора

Результаты поиска

Содержание BX-10M1

Отзывы:

Похожие инструкции для BX-10M1

Бренды по названию

Популярные бренды