Autronica AutoPath HC800 Скачать руководство пользователя страница 26

Страница: 26 / 50

Line of Sight Infrared Hydrocarbon Gas Detector AutroPath HC800 , 116-P-HC800/IGB, Rev. A, 2016-03-03

P/N 95-8744, v4.2 , rev. 3/16

Autronica Fire and Security AS

Page 22

StaRtup

When the AutroPath HC800 is installed and wired as

described in the “Installation” section, it is ready for

commissioning. If the application requires that specific

changes be made to the factory settings, HART

communication will be required.

NoTe

ensure that alarm devices are bypassed during
commissioning.

NoTe

The safety function (gas input-to-actuation/
notification) must always be verified upon
completion of installation and/or modification.

aliGnMEnt

oVeRVIew

The AutroPath HC800 modules must be properly

aligned before normal operation will be attained.

NoTe

Refer to the ATeX or IeCex Appendix for
information regarding the effect of misalignment
on system accuracy.

Important

Upon completion of system alignment, ensure
that

all

bolts on the AutroPath HC800 mounting

and alignment bracket are properly tightened.

24 VDC

–

B2653

250 TO 500

OHMS

+mA

INTR GND

RS-485 A

INTR A

SHIELD

+24 VDC

SPARE

+24 VDC

–mA

CAL

RS-485 B

INTR B

SHIELD

0V COM

HART

NOTE: THE HART HANDHELD DEVICE CAN BE CONNECTED EITHER TO THE

HART TERMINALS OR ACROSS THE LOAD RESISTOR.

Figure 20—Wiring the autropath Hc800 Receiver for benchtop

testing/programming using HaRt protocol

HART CONNECTORS

A2672

Figure 22—location of HaRt connector pins

(Receiver Module Shown)

C2667

+mA

INTR GND

RS-485 A

INTR A

SHIELD

+24 VDC

SPARE

+24 VDC

–mA

CAL

RS-485 B

INTR B

SHIELD

0V COM

HART

NOTE 1:

TOTAL LOOP RESISTANCE OF 4-20 MA CIRCUIT =

250 OHMS MINIMUM, 600 OHMS MAXIMUM.

NOTE 2: NOTE: SHIELDED CABLE RECOMMENDED (REQUIRED FOR ATEX).

CAUTION: DO NOT CONNECT THE COMMUNICATION LINK “INTR GND”

TERMINAL TO POWER SUPPLY COMMON OR ANY OTHER

GROUND CONNECTION.

INTR GND

RS-485 A

INTR A

SHIELD

+24 VDC

SPARE

RS-485 B

INTR B

SHIELD

0V COM

HART

TRANSMITTER

RECEIVER

24 VDC

–

4 to 20 MA

Figure 21— typical System Wiring including optional communication

link Wiring — Receiver Wired for non-isolated 4–20 ma current output

(Sinking)

Содержание AutoPath HC800



















































Результаты поиска

Содержание AutoPath HC800

Отзывы:

Похожие инструкции для AutoPath HC800

Бренды по названию

Популярные бренды

Autronica AutoPath HC800, Инструкция по эксплуатации

Результаты поиска

Содержание AutoPath HC800

Отзывы:

Похожие инструкции для AutoPath HC800

Бренды по названию

Популярные бренды