Autronica AutoPath HC800 Скачать руководство пользователя страница 47

Страница: 47 / 50

Line of Sight Infrared Hydrocarbon Gas Detector AutroPath HC800 , 116-P-HC800/IGB, Rev. A, 2016-03-03

P/N 95-8744, v4.2 , rev. 3/16

Autronica Fire and Security AS

Page 43

CoNNeCtIoNS AND HARDwARe

The HART Communicator can interface with the AutroPath HC800 from the control room or from any wiring

termination point in the analog output signal loop. To communicate, connect the HART communicator in parallel

with the AutroPath HC800 analog signal or load resistor. The connections are non-polarized. Refer to the “Wiring

Procedure” section for installation instructions.

NoTe

The HART Communicator needs a minimum of 250 ohms resistance in the loop to function properly. The
HART Communicator does not measure loop current directly.

oNLINe meNu

When HART communication is established with the receiver, the first menu displayed is the AutroPath HC800

Online menu:

OPGD RX Root Menu

1) Process Menu

2) Status Menu

3) Setup Menu

4) Calibration Menu

5) Test Menu

LS2000 RX Root Menu

1) Process Menu

2) Status Menu

3) Setup Menu

4) Calibration Menu

5) Test Menu

Status Menu

1) General Info Menu

2) Device Info Menu

3) Sensor Info Menu

4) Fault Status Menu

5) History Menu

Device Info Menu

1) Universal Rev.

2) Field Device Rev.

3) Software Rev.

4) Write Protect

5) RTC Menu

6) Alignment Status Menu

RTC Menu

1) Seconds

2) Minutes

3) Hours

4) Date

5) Month

6) Day

7) Year

8) Write Protect

OPGD RX Root Menu

1) Process Menu

2) Status Menu

3) Setup Menu

4) Calibration Menu

5) Test Menu

OPGD RX Root Menu

1) Process Menu

2) Status Menu

3) Setup Menu

4) Calibration Menu

5) Test Menu

Setup Menu

1) OPGD Option Menu

2) HART Output Menu

3) Com - 485 Menu

4) Config Flt Output Menu

5) Gas Type Menu

6) Range Menu

7) Alarm Menu

8) D/A Trim Method

9) RTC Menu

Alarm Menu

1) High Alarm Level

2) High Alarm Latch

3) Low Alarm Level

4) Low Alarm Latch

OPGD RX Root Menu

1) Process Menu

2) Status Menu

3) Setup Menu

4) Calibration Menu

5) Test Menu

Diag / Test Menu

1) Self Test

2) Response Test

3) Reset

4) Loop Test

5) Debug Menu

6) Alignment Menu

Alignment Menu

1) Quad X

2) Quad Y

3) Reference

4) Enable Alignment

5) Disable Alignment

OPGD RX Root Menu

1) Process Menu

2) Status Menu

3) Setup Menu

4) Calibration Menu

5) Test Menu

Online

1) Process Variables

2) Device Diagnostics

3) Configure/Setup

Calibration Menu

1) Gas Type

2) Cal Date

3) User Span Cal Delta

4) Zero Calibration Method

To select any of the menu options shown, highlight the desired option using the up/down arrow key, and then press

the “right arrow” key.

CommoNLy uSeD HARt CommANDS

The most commonly used HART commands for the AutroPath HC800 are:

1. Setting the real time clock

2. Setting alarm thresholds & latch/nonlatch functions

3. Setting the analog fault code menu

4. Performing full system alignment

5. Performing zero calibration

6. Assigning a nonvolatile tag name to the receiver

7. Defining a nonvolatile descriptor for future reference

8. Interrogating the history menu for information including total running hours, max/min temperature, calibration

and event logs.

Содержание AutoPath HC800



















































Результаты поиска

Содержание AutoPath HC800

Отзывы:

Похожие инструкции для AutoPath HC800

Бренды по названию

Популярные бренды

Autronica AutoPath HC800, Инструкция по эксплуатации

Результаты поиска

Содержание AutoPath HC800

Отзывы:

Похожие инструкции для AutoPath HC800

Бренды по названию

Популярные бренды