Autotrol 255-960, Руководство по эксплуатации и обслуживанию, Страница: 4 / 18

4
The front panel incorporates several important features
which allow you to know the status of your water
conditioner. These features are:
•
Regeneration Cycle Indicator. The white indicator
points to the status of the conditioner. Soft water is
available when the indicator points to
REGENERATION COMPLETE. Other positions
indicate that the conditioner is regenerating the
resin bed and only hard water is available.
•
Four-Digit Display. The four-digit red LED display
shows system information such as time of day,
gallons of conditioned water available, time the
conditioner will regenerate, or any error alarms.
•
Green Indicator Lights. The green indicator lights
are located at the right of the control panel.
•
TIME OF DAY
•
TIME OF REGEN
•
HARDNESS
•
SALT AMOUNT
•
CAPACITY
•
REGEN TIME REMAINING
When a green light is on next to one of the six control
legends, the LED display provides information
pertaining to that legend. When conditioned water is
available, the display alternates between TIME OF DAY
and CAPACITY and the corresponding green lights
alternate between these control legends.
•
Programming Push Buttons. The programming
buttons are located at the bottom of the panel
under the display. Use the buttons to look at or
change the conditioner settings.
•
REGEN Push Button. The REGEN button is
located at the bottom of the panel below the six
indicator lights. Press the button to start a
regeneration of the water conditioner.
Note: If you press the button again a minute or more
after regeneration begins, a second regeneration will
start when the first regeneration is complete. The
display freezes with the REGEN TIME REMAINING
information. After the first regeneration is complete, the
second regeneration begins immediately. The display
will alternate between the TIME OF DAY and REGEN
TIME REMAINING.
Control Settings Control Settings Control Settings Control Settings
General Information
Use the four programming push buttons to change any
of the control settings. Settings can only be changed if
the regeneration cycle indicator is pointing at
REGENERATION COMPLETE. If you try to change a
setting when the cycle indicator is in any other position
or if the setting is not valid, the control beeps to let you
know that the new setting has been ignored.
To change a setting: Press the down arrow [
↓
] button
until the green light is illuminated next to the control
setting you want to change. That control setting value
shows on the display. Press the SET button and the far
right number on the display starts flashing. If you want
to change the number, press the up arrow [
↑
] button to
increase the number or the down arrow [
↓
] button to
decrease the number. To skip the number without
changing, press the left arrow [
←
] button.
Note: If you press and hold either the up arrow [
↑
]
button or the down arrow [
↓
] button for more than one
second, the flashing number will scroll up or down.
When the number is correct, press the left arrow [
←
]
button. The first number stops flashing and the next
number starts flashing. You can only change the
flashing number. Continue changing numbers until you
reach the desired setting. Press the SET button. The
numbers stop flashing and the control accepts the new
setting. After approximately 30 seconds, the control
starts alternating the display between TIME OF DAY
and CAPACITY.
Note: If a beep sounds, the new setting is not accepted
because it was outside the range of allowable values.
The old setting will be shown on the display.
Time of Day Clock
The control uses the Time of Day clock and the amount
of conditioned water remaining to decide when to
begin a regeneration. When a regeneration is necessary
and the Time of Day clock is at the same time as the
Time of Regeneration setting, the control starts the
regeneration.
When the green light is on next to the TIME OF DAY
legend, the display is showing the time that the control
thinks is correct. If you need to change the Time of Day,
refer to the instructions later in this section. The Time of
Day displays time in hours and minutes separated by a
colon[:]. When the colon is flashing on and off, water is
flowing through the conditioner. There is a small red dot
in the upper left corner near the p.m. letters to indicate
p.m. for 12-hour clocks. When the dot is off, the time is
a.m. You can set the clock for any time, a.m. or p.m.
Complete the following steps to change the Time of
Day:
1. Press the down arrow [
↓
] button until the green light
next to the TIME OF DAY legend is on.
2. Press the SET button and the minute number on
the display starts flashing. If you want to change
this number, press the up arrow [
↑
] button to
increase the number or the down arrow [
↓
] button
to decrease the number. To skip the number
without changing, press the left arrow [
←
] button.
3. When the number is correct, press the left arrow
[
←
] button. The first number stops flashing and the