Autotether Wireless Lanyard Standard System Скачать руководство пользователя

Страница: 20 / 25

“The Screamer” Autotether Wireless Man Overboard

Alarm System

Operation

All directions outlined above for the Standard Wireless Lanyard System

apply to the Alarm System. The exceptions are:

There is no kill switch clip.

All FOBs have the same function.

There is no function for FOB Dipswitch 2 or 3. FOB dipswitch 4
functions by changing channels in the alarm system.

Operation (page 13) see below for the alarm operation.

Alarms and Faults function is different with the alarm system,
please see instructions below for

The audible alarm is pulsating and much louder (105 dB) than
the wireless lanyard system.

Once your AUTOTETHER

Alarm System is installed, turned on and

tested, it’s ready for operation.

Scenario # 1

– You are alone on the motorboat or sailboat and towing

a dinghy and getting ready to get underway. AUTOTETHER

is ON and

a FOB has been placed in the dinghy. The Host has registered the FOB,
all system indicators are flashing GREEN. Your dinghy breaks loose.

When the FOB in the dinghy goes beyond approximately 150 feet the

AUTOTETHER

alarm sounds.

You turn your boat around and go pick up your dinghy. Press the RESET

button to silence the alarm. Once reattached to your boat press the
POWER button to re-initialize the system and register your FOB.

Scenario # 2

– You are enjoying a day or evening of sailing with

several passengers. You are all wearing your AUTOTETHER

FOBs and

the system is flashing GREEN. One of your passengers falls overboard.
As soon as the AUTOTETHER

FOB is submerged the AUTOTETHER

alarm sounds and lights go steady red. You press the RESET button to

silence the alarm. You maneuver to pick up your passenger, who is
wearing a USCG approved flotation device.

While you are maneuvering to pick up your passenger you notice that

one of the FOB Signal LEDs is RED – it belongs to the passenger who fell
overboard. Everyone else in the boat is still being monitored by

AUTOTETHER

. You pick up your overboard passenger and, once the

passenger is safely aboard, you press the Host POWER button to re-

Содержание Wireless Lanyard Standard System


























Результаты поиска

Содержание Wireless Lanyard Standard System

Отзывы:

Похожие инструкции для Wireless Lanyard Standard System

Бренды по названию

Популярные бренды

Autotether Wireless Lanyard Standard System, Руководство пользователя

Результаты поиска

Содержание Wireless Lanyard Standard System

Отзывы:

Похожие инструкции для Wireless Lanyard Standard System

Бренды по названию

Популярные бренды