Autostart AS PRG-1000 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 9

Autostart AS PRG-1000 Скачать руководство пользователя страница 6

P.6

http://www.autostart.ca

Quick Installation Guide

OPTION 2*

Toggle ON/OFF – max 30 sec.

OPTION 3

Toggle ON/OFF – max 4 min. (only when running remotely)

OPTION 4

Negative Starter output

FUNCTION 4 – AUX 3 / Trunk output

OPTION 1

1-sec. output

OPTION 2*

Constant output

OPTION 3

Trunk output with disarm and rearm pulses

FUNCTION 5 – External Trigger

OPTION 1

Zone 3 with disarm/rearm (

TRUNK

monitor)

OPTION 2*

Key sense

OPTION 3

Engine

START/STOP

OPTION 4

SmartStart™

MODE 4

* INDICATES DEFAULT SETTING

FUNCTION 1 – Alarm control

OPTION 1

ENABLED

(HORN must be enabled in MODE 3 FUNCTION 2, option 1 or 3)

OPTION 2*

DISABLED

FUNCTION 2 – Ready Mode Option / Hybrid Option

OPTION 1

ENABLED

by handbrake

OPTION 2*

ENABLED by remote

OPTION 3

Hybrid option

ENABLED

FUNCTION 3 – Ready Mode completion option

OPTION 1

Open/Close door

OPTION 2*

Remote

OPTION 3

Open/Close door with automatic door-lock

FUNCTION 4 –

Bypass

OPTION 1

ADS (1-way D2D)

OPTION 2*

Xpresskit

(2-way D2D)

OPTION 3

Fortin (1-way D2D)

FUNCTION 5 – Push-To-Start option

OPTION 1

Push-To-Start

ENABLED

OPTION 2*

Push-To-Start DISABLED

OPTION 3

Push-To-Start

ENABLED

with take over within 1.5 min.

OPTION 4

Push-To-Start

ENABLED

with take over within 3 min.

HORN ADJUSTMENT

Note: Before adjustment, horn option must be installed and enabled.

1.

In programming mode

(page 3).

2.

Press and hold the brake pedal, then simultaneously press the

UNLOCK

and

START/STOP

buttons



the horn will chirp 5 times.

3.

Release the brake pedal.

4.

To change the timing:

1.

To increase the horn pulse by 3 ms, press the

LOCK

button.

2.

To decrease the pulse by 3 ms, press the

UNLOCK

button.

3.

To increase the pulse by 10 ms, press the

START/STOP

button.

4.

To decrease the pulse by 10 ms, press the

TRUNK

button.

5.

To save the new settings: press

LOCK

and

UNLOCK

simultaneously. If 3 chirps are returned, the new

setting has been saved.

6.

You have 20 more seconds to select one of the sub-menus if needed.

SETTING UP THE TACH

VIRTUAL TACH ADJUSTMENT

Warning: For automatic transmissions only.

Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to
develop. VTS is able to effectively monitor the engine starting sequence and release the starter at the right time
without physically connecting the tach wire to the remote starter. The VTS constantly monitors the data and
readjusts itself automatically in order to maximize its capability to start the engine properly in any weather or
deteriorating battery condition

.

OPTIONAL TIME DELAY ADJUSTMENT IN VIRTUAL TACH SYSTEM

«
...
4
5
6
7
8
...
»

Содержание AS PRG-1000










Отзывы:

Нет отзывов