Autostart AS-1585 SH Скачать руководство пользователя страница 15

Страница: 15 / 25

AS-1585 SH

Installation Guide

P. 15

FUNCTION 5 – LED flashing

OPTION 1*

ENABLED

OPTION 2

DISABLED

OPTION 3

DISABLED

MODE 2

* INDICATES DEFAULT SETTING

FUNCTION 1 – Safe Start.

OPTION 1

Safe Start

ENABLED

OPTION 2*

Safe Start

DISABLED

OPTION 3

“Swap Start” – enhanced Safe Start Mode with extended safety:
To start the Engine: press the

LOCK

and

UNLOCK

buttons simultaneously

To trigger

AUX 2

: press the

START

button

FUNCTION 2 – Engine Run Time

OPTION 1

Run Time = 4 minutes in

GAS

mode / 9 minutes

DIESEL

mode

OPTION 2*

Run Time = 15 minutes in

GAS

mode / 20 minutes

DIESEL

mode

OPTION 3

Run Time = 25 minutes in

GAS

mode / 30 minutes

DIESEL

mode

FUNCTION 3 – Turbo Mode

OPTION 1

Turbo Mode

ENABLED

OPTION 2*

Turbo Mode

DISABLED

OPTION 3

Turbo Mode

ENABLED

FUNCTION 4 – Engine type and Cold Weather Mode

OPTION 1

Diesel Mode with 20-minute Run Time in Cold Weather Mode

OPTION 2*

Gas Mode with 4-minute Run Time in Cold Weather Mode

OPTION 3

Diesel Mode with 9-minute Run Time in Cold Weather Mode

FUNCTION 5 – Ignition Valet

OPTION 1

Ignition Valet

DISABLED

OPTION 2*

Ignition Valet

ENABLED

OPTION 3

Ignition Valet

ENABLED

MODE 3

* INDICATES DEFAULT SETTING

FUNCTION 1 – Home Valet

OPTION 1

Home Valet

ENABLED

OPTION 2*

Home Valet

DISABLED

OPTION 3

Home Valet

DISABLED

FUNCTION 2 –

AUX 3

/ Zone 3 Programming

OPTION 1

1-sec. output when

TRUNK

button is pressed for 3 sec. with Ignition

OFF

or under remote run

OPTION 2*

Constant output while the

TRUNK

button is pressed

OPTION 3

Output with Disarm and Rearm pulses

FUNCTION 3 –

AUX 2

Programming

OPTION 1

Constant output while the

LOCK

and

UNLOCK

buttons are pressed.

In Safe Start Mode: activate

AUX 2

by pressing the

START

button.

OPTION 2*

Toggle

ON/OFF

(with 30-second timeout)

OPTION 2

Horn confirmation when lock.

OPTION 4

Priority Door Access

FUNCTION 5 – External Trigger

OPTION 1

Zone 3 disarm/rearm (Trunk Pin: a disarm pulse is sent before the Trunk
opens, the vehicle rearms 4 seconds after the Trunk is closed).

Содержание AS-1585 SH


























Результаты поиска

Содержание AS-1585 SH

Отзывы:

Бренды по названию

Популярные бренды

Autostart AS-1585 SH, Руководство по установке

Результаты поиска

Содержание AS-1585 SH

Отзывы:

Бренды по названию

Популярные бренды