background image

4

Basic Functions

1.

A special combination of buttons presses is used to start the heater with a 
remote control key. Firstly press “Lamp” button on the key to switch on the
car’s lighting. Then press “Lock” button two times within 30 seconds, while 
lighting is on. Every “Lock” button’s pressing should be confirmed with 
direction indicators flashing.

2.

To stop the heater by using a remote control key, twice switch on and then 
switch off car’s lighting from the key. Intervals between “Lamp” button 
presses should not exceed 20 seconds.

3.

It is possible to disable remotely startups of the heater, programmed in the 
CIP. Use a remote control key to send stop command when the heater is idle. 
Starting the heater any way or turning the ignition to “on” position enables
CIP timers again. 

Additional Functions

By default the module is adjusted to perform only basic functions, such as 

start and stop of the heater by using a remote control key. To turn on additional 
functions such as flashing with direction indicators in rearview mirrors, etc. enter 
the module into Setup mode and activate corresponding setup item (see settings 
table 3).

The buttons of the left-hand stalk switch and the brakes pedal are used to 

enter Setup mode and to change the settings. It is necessary to stop the engine and 
the heater before. Turn the ignition on by holding the engine start button for at 
least 2 seconds, then press and hold the brakes pedal. Next press and hold for at 
least 5 seconds “Read” button (also can be marked as “OK” button in some cars), 
while module’s LED flashes once a second. Both direction indicators in the CIP 
confirm entering to the setup mode with 2 flashes*. Release the brakes pedal and 
“Read/OK” button finally. 

Each setup item in the settings table is a 3-digit code. To enter a digit of a 

code, shortly press “RESET” button so much times, as corresponds to a digit. The 
LED and the direction indicators symbols in the CIP confirm each button press: the 
LED briefly goes off, the left direction indicator flashes one time when the first or 
the third digit of code is entered, the right direction indicator - when the second 
digit of code is entered. To complete a digit entering, press and release “Read/OK” 
button.  The CIP confirms it with one flash of both direction indicators 
simultaneously. When all three digits entered, the module checks the code for 
validity and confirms it with the direction indicators flashing. The both direction 
indicators flash twice simultaneously in case of valid code and flash twice 
alternately in case of invalid code. 

Содержание Key-V2









Отзывы: