-|Transparent Guide|-
Product Components
•
Product
•
Instruction manual
•
Ethernet connector Cap
(screw plug - waterproof) × 1
Software
Download the installation file and the manuals from the Autonics website.
■
atVision
The program allows setting of smart camera parameters and management of
monitoring data such as inspection status and status information.
Item
Minimum requirements
CPU
Intel i3, Ryzen 3 or above
OS
Microsoft Windows 7 (×64) or higher
RAM
6 GB or higher
Storage
01)
at least 10 GB of available HDD space
Resolution
02)
1280×800 or higher (1920×1080 recommended)
Others
RJ45 Ethernet port, GigE network interface card
01) Additional HDD space may be required depending on the number of inspections.
02) This software is optimized for 1920×1080 resolution and 100% magnification.
Inner Circuit
■ Trigger (TRIG) input
Trigger-
CIRC
UIT
VC Series
External
■ NPN open collector output
■ PNP open collector output
CIRC
UIT
LOAD
OCP
SCP
Max. 100 mA
CIRC
UIT
LOAD
OCP
SCP
Max. 100 mA
•
OCP (over current protection), SCP (short circuit protection)
•
If short-circuit the control output terminal or supply current over the rated specification, normal control signal is
not output due to the output short over current protection circuit.
Connections
■ Power I/O connector wiring (M12 8-pin plug type connector)
•
When the power is unstable, ground the shield of the provided cable.
Pin Color
Signal
Function
1
White
HS OUT 0 Strobe OUT
2
Brown
VCC
Power input
3
Green TRIG +
Trigger input +
4
Yellow
TRIG -
Trigger input -
5
Gray
RS232 RX RS232 receive
6
Pink
RS232 TX RS232 transmit
7
Blue
GND
Ground
8
Red
HS OUT 1 Select 1 from inspection complete,
inspection result output (PASS / FAIL), alarm
8
7
5
6
3
1
4
2
■ Ethernet connector wiring (M12 8-pin socket type / RJ45 connector)
M12 8-pin
Color
RJ45
Signal
1
White / Blue
5
BI_DC-
2
White / Brown
7
BI_DD+
3
Brown
8
BI_DD-
4
Orange
2
BI_DA-
5
White / Green
3
BI_DB+
6
White / Orange
1
BI_DA+
7
Blue
4
BI_DC+
8
Green
6
BI_DB-
8
7
4
3
2
6
1
5
Network Setting
•
Configure the network settings of vision sensor via atVision.
•
For initial IP address, refer to the table as below.
IP address
192.168.0.2
Subnet mask
255.255.255.0
Gateway
192.168.0.1
Sold Separately
•
Power I/O cable: CIDM8-□-A (I type), CLDM8-□-A (L type)
•
Ethernet cable: C1(M)8-□PR-A (I type), C4(M)8-□PR-A (L type)
•
Waterproof lens cover: HL-▭-VC
Waterproof Lens Cover Assembly
02
01
03
04
01.
Remove the housing bushing cover by rotating CCW direction.
02.
Remove the sensor protective cap.
03.
Tighten the C-mount lens by rotating CW direction.
04.
Tighten firmly the waterproof lens cover by rotating CW direction until there
is no gap.
Unit Descriptions
01
02
04
03
05
01.
Sensor protective cap
02.
Housing bushing cover
03.
Status LED indicator
04.
Power I/O connector
05. Ethernet connector
■
Indicator
Indicator Name
Function
POWER
Power indicator (green)
Turns ON when power is supplied.
LINK
Ethernet connection indicator (green) Turns ON when vision sensor is connected
with PC (Ethernet communication).
DATA
Data transmit indicator (green)
Flashes when data is transmitted between
smart camera and PC.
USER 1
User setting indicator (green / red)
Turns ON or flashes in operation of
inspection complete, inspection result
(PASS, FAIL), alarm, camera work
USER 2
Dimensions
•
Unit: mm, For the detailed drawings, follow the Autonics website.
72
Ø55.6
87.5
18.5
30
36
4-M4×P0.7
DP 6.0
62.3
Ø69.0
138.5
46.5
120
136.6
50
10.6
98
4-M4×P0.7
DP 7.0
106.5 / 123.5
Ø63.4
46.5
120
136.6
