Automatic Technology GDO-9v2 Enduro Gen 2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 36

background image

Owner Installation Instructions

GDO-9v2 SecuraLift®

7

SmartSolar™ and Battery Back Up Compatibility (optional)

The opener can be ﬁ tted with a SmartSolar™ or Battery Back Up kit for operation in the

event of a power outage, or where mains power access is not available.

NOTE:

If the

door is the only entrance to the garage, and a battery back up kit is not ﬁ tted, a

keyed cable release should be ﬁ tted external to the garage.

Vacation mode

A hand held transmitter can be programmed to lock and unlock all other

transmitters that have been programmed into the openers’ memory. The vacation
mode can be used when the door is left idle for long periods of time.

Pet/Pedestrian mode

The transmitter can be programmed to open the door to an adjustable partial

height so that the family pet can enter and exit the garage at any time. You may

also wish to open the door to a height suitable only for pedestrian access.

Auto-close mode

The opener can be programmed to automatically close after an open cycle. The auto-

close time is adjustable. It is compulsory to install a P.E. Beam if this mode is selected,

otherwise the door may cause personal injury or damage to property.

Photo Electric (P.E.) Beam (optional)

The opener has an input to connect a P.E. Beam for extra safety and use of the auto-close

mode.

Manual operation

The opener is equipped with a unique manual disengaging device. If the power to the opener is disrupted the
door can be put into manual mode by pulling down on the string handle on an angle towards the door. This
allows for manual operation of the door. To re-engage the opener pull the string handle away from the door.

«
...
5
6
7
8
9
...
»

Содержание GDO-9v2 Enduro Gen 2





































Отзывы:

Нет отзывов

Похожие инструкции для GDO-9v2 Enduro Gen 2

Бренд: Calimet Страницы: 21

Бренд: Calimet Страницы: 16

Бренд: White Rose Страницы: 29

Бренд: Telcoma Страницы: 16

Бренд: GBD Страницы: 8

Бренд: CAME Страницы: 30

Бренд: Tower Hobbies Страницы: 16

Бренд: tousek Страницы: 48

Бренд: DKS Страницы: 42

Бренд: DKS Страницы: 48

Бренд: SOMFY Страницы: 52

Security+ 4620DI

Бренд: Doit Страницы: 40

BelFox Fabia 50

Бренд: Bauer Страницы: 16

Бренд: Elite Страницы: 40

Бренд: 1TAC Страницы: 2

Бренд: Serai Страницы: 12

MERCURIO 524A F

Бренд: Serai Страницы: 16

Бренд: FAAC Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды