Automatic Technology GDO-9V1 SecuraLift Скачать руководство пользователя страница 24

Страница: 24 / 28

PARAMETERS

DOOR STATUS INDICATORS

BUTTON

FUNCTION

Operate

Opens/Stops/Closes the door

Door Code

Codes a transmitter button for Operate function

Light Code

Codes a transmitter button for light function

Door Code & Minus (-)

Codes a transmitter button for pet (pedestrian) function

Light Code & Minus (-)

Codes a transmitter button for vacation function

Force Margin Set & Pus (+)

Increases the obstruction force margin setting

Force Margin Set & Minus (-)

Decreases the obstruction force margin setting

Force Margin Set (then) Set

Reloads the factory set default obstruction force margin setting

Auto Close Time (then) Plus (+)

Increases the auto close delay time

Auto Close Time (then) Minus (-)

Decreases the auto close delay time

Auto Close Time (then) Set

Reloads the factory set default auto close delay time

Force Margin Set & Auto Close Time (then) Plus (+)

Each press of the open button increases the light time by 10 secs.

Force Margin Set & Auto Close Time (then) Minus (-)

Each press of the open button decreases the light time by 10 secs.

Force Margin Set & Auto Close Time (then) Set

Reloads the factory set default light time

Minus (-) (for 6 secs.)

Clears the door limits set positions. Limits then need to be reset.

Set & Close (for 2 secs.)

Enters pet (pedestrian) position mode.

Set (the power on) and hold until all LEDs are off

Deletes control parameters excluding transmitter storage memory.

Door Code (the power on) and hold until all LEDs are off

Deletes all transmitter storage memory.

Set & Door Code (the power on) and hold until all LEDs are off

Deletes all control parameters and transmitter storage memory.

Set

Re initialises opener obstruction force margin.

DOOR OPENER STATE

OPEN LED GREEN

CLOSE LED

RED

DOOR STATUS

LED YELLOW

BEEPER

OPEN

OPENING

FLASHING

CLOSING

FLASHING

DOOR TRAVEL STOPPED

FLASHING

DOOR OBSTRUCTED WHEN OPENING

FLASHING

DOOR OBSTRUCTED WHEN CLOSING

FLASHING

BEEPS WHILE

DOOR IS MOVING

OPENER OVERLOADED

ALTERNATING

FLASHES

ALTERNATING

FLASHES

DOOR IN OPEN POSITION WITH
AUTO CLOSE MODE SELECTED

ONE SECOND

FLASHES

MAINS POWER INTERRUPTED

RAPID

FLASHES

Содержание GDO-9V1 SecuraLift





























Результаты поиска

Содержание GDO-9V1 SecuraLift

Отзывы:

Бренды по названию

Популярные бренды

Automatic Technology GDO-9V1 SecuraLift, Руководство по установке

Результаты поиска

Содержание GDO-9V1 SecuraLift

Отзывы:

Бренды по названию

Популярные бренды