Automatic Technology GDO-6v3 EasyRoller Скачать руководство пользователя | Manualshive

Страница: 21 / 36

background image

Owner Installation Instructions

GDO-6v3 EasyRoller

®

21

27

ﬁ g

Deleting Transmitter Codes

Step 13.1 - Deleting a Stored Transmitter
Code

Select the transmitter you want to delete.
Press and hold the DOOR CODE BUTTON

(Fig.

27).

Press the transmitter button you would like to
delete for two (2) seconds, pause for two (2)
seconds, press again for two (2) seconds and then
release.
Release the DOOR CODE BUTTON. The code
should now be deleted. Conﬁ rm this by pressing
the transmitter button - the function (e.g. door
opening) should not respond.

Step 13.2 - Deleting All Transmitter Codes

Turn off power to the opener.
While switched off, press and hold the DOOR
CODE BUTTON

(Fig. 27).

Turn on the power to

the opener while holding this button.
The OPEN LIMIT, CLOSE LIMIT and DOOR
STATUS LED’s will illuminate for about ﬁ ve
(5) seconds. These LED’s will turn off and the
CODING LED will illuminate.
Release the DOOR CODE BUTTON. All stored
codes will now be deleted. Conﬁ rm this by
pressing buttons on any previously coded
transmitters - the opener should not respond.

a.
b.

c.

d.

a.
b.

c.

d.

«
...
19
20
21
22
23
...
»

Содержание GDO-6v3 EasyRoller





































Отзывы:

Нет отзывов

Похожие инструкции для GDO-6v3 EasyRoller

Бренд: Overhead door Страницы: 6

Бренд: Ribind Страницы: 12

Бренд: Nice Страницы: 36

Бренд: Nice Страницы: 48

Marantec Control 44

Бренд: Deltadoors Страницы: 52

Бренд: Nice Страницы: 28

Бренд: Nice Страницы: 44

Бренд: Vartai Страницы: 19

Бренд: TOPP Страницы: 60

Бренд: CAB Страницы: 32

Бренд: Smart Openers Страницы: 12

Бренд: Beninca Страницы: 24

Walk-n-Cut 76500

Бренд: Hamilton Beach Страницы: 15

Бренд: Daspi Страницы: 24

Бренд: CAME Страницы: 24

Бренд: Automatic Technology Страницы: 48

IDrive 3651-372

Бренд: Wayne-Dalton Страницы: 42

Бренд: GiBiDi Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды