2
GDO-10V3L2 Toro
™
Owner Installation Instructions
GDO-10V3L2 Toro
™
Roll Up Garage Door Opener
Contents
1. Important Safety Instructions
3
2. Controller Input And Outputs
4
3. Operating Controls
5
4. Set Up Requirements
6
4.1 Kit Contents
6
4.2 Choosing your Set up
6
5. Pre-Installation Requirements
7
5.1 Door Operation
7
5.2 Unsuitable Door Types
7
5.3 Position
7
5.4 Power Supply
7
5.5 Sideroom
7
5.6 Forks
7
6. Installation
8
6.1 Preparation
8
6.2 Fitting The Opener
8
6.3 Mounting The Opener
8
6.4 Installing The Wall Mounted Control Unit
9
7. Programming The Opener
9
8. Setting Limits
10
8.1 Setting Travel Limits
10
8.2 Code A Transmitter For Limit Setting
11
8.3 Setting Limits Via Transmitter
11
9. Coding Transmitter
12
9.1 Coding Transmitter Button
12
9.2 Selecting Function Of The Button
12
9.3 Returning To Main Screen
12
10. Remotely Coding Transmitters
13
10.1 Selecting The Function To Be Coded
13
10.2 Activate Remote Code Set Mode
13
11. Setting Pedestrian Position
13
11.1 Setting Pedestrian Position
13
11.2 Checking Pedestrian Position
13
11.3 Error Displays
13
12. Safety Obstruction Force Test
14
12.1 Testing Close Cycle
14
12.2 Testing Open Cycle
14
12.3 Adjusting the Safety Obstruction Force.
14
12.4 To Recalculate Force Margins
14
13. Safety Close & Auto-Close Mode
15
13.1 Safety Close Mode
15
13.2 Setting Up Satndard Auto-Close Mode
15
13.3 Safety Beam Triggered Auto Close
15
13.4 Pedestrian Auto-Close
15
13.5 Auto-Close After Obstruction:
15
14. Time Clock
16
14.1 Time Clock Operation
16
14.2 Time Clock Settings
16
14.3 Day Light Saving Time Adjustment
17
15. Accessories Installation
17
15.1 Fitting Courtesy Lights
17
15.2 Fitting Solenoid Or Magnetic Locks
17
16. Battery Replacement
18
16.1 Replacing Backup Batteries
18
16.2 Replacing Transmitter Batteries 18
17. Battery Disposal
18
18. Specifications
19
19. Troubleshooting
20
20. Maintenance
21
20.1 Door Maintenance
21
20.2 Lubrication (every 3 - 6 months)
21
20.3 Door Service and Repair
21
20.4 Opener Maintenance
21
20.5 Service Indicator
21
21. Appendix
22
A - Console Menu Structure
22
B - Viewing & Editing Logic Console Parameters
24
C - Control Board Adjustments
25
D - Diagnostic Tools
27
E - Memory Tools
28
F- Transmitter Editing
29
G - Transmitter Management
31
22. Warranty and Exclusion of Liability
32
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or
otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic
Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any
person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener in accordance with these
installation instructions.
WARNING!
• The door may operate unexpectedly, therefore do not allow anything to stay in the path
of the door.
• For
Safety
protection, a Safety Beam
must
be fitted with logic console. Failure to comply
will void the warranty and may result in serious personal injury and/or property damage .
• The drive must not be used with a door incorporating a wicket door, unless the drive cannot
be operated with the wicket door open.
• The drive is intended to be installed at least 2.5m above the floor.
• DO NOT
allow children to operate the opener. Any device that can operate the opener,
make sure it is out of reach of children and that the doorway is in full view at all times. Serious
personal injury and/or property damage can result from failure to follow this warning.
• When using auto close mode, a
Safety
(Photo Electric)
Beam
must be fitted correctly and
tested for operation at regular intervals.
Extreme caution
is recommended when using
auto close mode.
All safety rules
must be followed.
ELECTROCUTION!
• Place opener in protected area so that it does not get wet.
• Do not spray with water .
• Disconnect the power cord
from mains power before making any repairs or removing
covers. Only
experienced
service personnel should remove covers from the opener.
• If the power supply cord is damaged, it
must
be replaced by an Automatic Technology
service agent or suitably qualified person.
• Electrical wiring must be compliance with the local building an electrical codes.
