Automatic Products SNACKSHOP LCM3 Series, Инструкция по эксплуатации

Страница: 8 / 81

components
components
4
installation
1. Leveling the Machine on location is important for the prop-
er function of the machine. The four leveling screws in the
legs are the means of leveling the machine. After positioning
the machine, level machine in front to rear and right to left
directions. After leveling, turn front right (lock side) leveling
screw in about one-half turn to drop this corner slightly to
make the door easier to close and lock.
2. Vo l t age and Polarity Check . It is important that this
machine is hooked up to the proper voltage and polarity.
Using a voltmeter, perform the following checks from the
illustration shown.
3. Loading Snack Shelves. Open door to full open position,
push down on white and gray plastic lock levers (Figure 1.)
on right side panel by shelf to unlock shelf, holding lever
down. Grasp the shelf slightly and pull forward until shelf
reaches its stop. The shelves tilt down (do not drop) to make
loading easier.
Only one product shelf should be in the
loading position at a time. When returning a shelf, be sure
the shelf is in its full home or vend position. Begin loading
with the top shelf. Move it to the loading position.The height
spacing for items is greatest in this shelf and the tallest
bagged items should be placed there. Soft items, such as
pastry, pies, etc., should be placed in the lowest snack shelf,
making the drop distance as short as possible.
IMPORTANT: Product must not be forced into the spiral
spaces but should fit freely. If the product is too tight, use a
larger pitch spiral. The bottom of the product should be
placed on top of the spiral wire that rests on the shelf sur-
face. (Figure 2.) The width of the product must be greater
than the diameter of the snack spiral. If it is smaller, the
product may fall through when it is in the front, ready to vend
position.
4. Removal of Spiral. Grasp the front of the spiral and turn it
clockwise. Lift the spiral up and off of the spiral lock and turn
the spiral counterclockwise to lock it in place. Be sure the
front end of the spiral is positioned properly (with the front
end of the spiral pointing downward on the left side). (Figure
3.) The spiral lock is attached between the spiral retainer
tabs. Give a light forward pull on front of the spiral to check
if it is locked in place.
5. Product Spacers, 5-Selection Shelf. A product spacer is
used to reduce the width of the product area and should be
used on any 5-selection snack shelf where the product width
is 4-1/2'' or less. Spacers should fit within 1/8'' of the product
but should not fit tight against the product. There are three
positions in each snack space where these spacers can be
placed. To install the spacer, align the lock ears (on the lower
edge of the spacer) with one of the three sets of slots (one
front and one rear). (Figure 4.) Push the spacer to the rear
to allow the ears to enter the slots, then allow the spacer to
m ove fo r wa r d . Be sure the ears are in the same set of slots,
Figure 2. Placement of product on main product snack
shelves and front end position of spiral.
Figure 3. Removing and installing spiral.
CAUTION:
THIS MACHINE IS DESIGNED
FOR INDOOR USAGE ONLY. ANY
OTHER USAGE MAY VOID THE
MANUFACTURERS WARRANTY.
CAUTION:
THE FOLLOWING
PROCEDURE REQUIRES THAT THE
MACHINE HAVE POWER APPLIED AND
A POTENTIAL ELECTRICAL SHOCK
HAZARD EXISTS.
(A)
(B)
(C)
(A) to (B) = 120 VAC (+-10%)
(A) to (C) = less than 1 VAC
(B) to (C) = 120 VAC (+-10%)
A. C. HOT (B)
A. C. NEUT (A)
EARTH (C)
GROUND
NOTE: Should the readings be different from above,
have a certified electrician correct the problem.
Figure 1. Moving shelf to loading position