background image

 Autopilots

  Autopilots Service Manual   83115-1

Warning

CE Marking of Equipment/Replacement Parts

If the Autohelm equipment under repair, test, calibration, installation or setting to work carries the European CE mark,

only parts and components supplied or approved for such use by Raytheon should be used in order to maintain

compliance with the relevant CE requirements.

Incorporation, use or attachment, by any means, of parts or components not supplied for or not approved for such use by

Raytheon or, if supplied or approved for use by Raytheon, not properly fitted in accordance with instructions published,

provided or recommended by Raytheon, may cause the equipment to malfunction and, in particular, to become unsafe or

to no longer meet the relevant CE requirements. In these circumstances, Raytheon Marine Europe Ltd excludes liability

to the fullest extent permissible in law for any loss or damage including any liability for its contribution to such loss or

damage by its negligent acts or omissions .

   Autopilots Service Manual

For use on

Z326, Wheel Autopilot

Z327, Tiller Autopilot

Z332, Tiller GP Autopilot

D3730-1

All manuals and user guides at all-guides.com

all-guides.com

Содержание ST4000+



































Отзывы: