Auto Meter BVA-460 Скачать руководство пользователя страница 28

Страница: 28 / 30

TROUBLESHOOTING

PROBLEM

SOLUTION

The Control Module will not turn on.

• On the Control module hold the power button on for at least 5 seconds.

• If the Control Modules still does not turn on, place

the Control Module into the Load Module.

• Plug the charger into the Load Module and look for the Load Module’s

LED to go to a blinking red. This will indicate that the Control Modules is

being charged.

• Let the Control Module charge for at least 3 hours.

The Load Module LED is off.

• Remove the Control Module and press the Load Module button for one

second.

• The LED should turn red for about a second then turn green.

• If the LED still does not turn on, the Load module battery may need

recharging.

• Plug in the charger and connect it to the Load Module. The LED should

stay a steady red while charging. Let the Load module charge for 3

hours.

• Note: Both the Control module and Load module batteries will be

charged if the clamps are connected to a fully charged 12V battery.

The Control Module will not make

a Bluetooth connection to the Load

Module

• Shut down the Control Module by holding the power button down for 1

second.

• Press the Power off button on the screen when it appears.

• Answer OK, to the Power off prompt.

• On the Load Module. Press the button for about two seconds. This will

reset the Load Module. The LED will blink Red twice and then go off for

less than a second, then turn Red, then turn Green

• On the Control module hold the power button on for at least 5 seconds to

turn it back on.

• When the Auto Meter application loads, the Modules should now

automatically connect.

The BVA-460 says I need to connect

the clamps when I have already

connected them.

• Make sure the both jaws of the clamps have a good connection.

• Clean any corrosion from the battery post and the clamps.

• If the battery is completely dead, (Voltage less than 1 volt.) the BVA-460

will not detect the battery. Charge the battery before testing.

I have tested a battery and got a

Charge and Test result after I have

charged the battery.

• A Charge and Test results occurs when the battery voltage is not high

enough to perform an accurate test.

• Make sure your charger is working properly.

• The battery may not be taking a charge thus it can be rated as a bad

battery if you continue to get a Charge and Test result.

Completely Discharged Tablet Battery Recognize a completely discharged tablet battery when the power button

is pressed and held and the outline of a battery appears on the screen. To

recover, plug the external charger into the tablet.

To power on tablet while tablet is

charging.

Press and hold power button until Auto Meter Logo appears. A few seconds

later a battery outline will appear. When it does press and hold the power

button again while the battery outline is visible. Once the battery outline

goes away, release the button.. The Auto Meter Logo will reappear and the

tablet will continue to boot.

Содержание BVA-460































Результаты поиска

Содержание BVA-460

Отзывы:

Похожие инструкции для BVA-460

Бренды по названию

Популярные бренды

Auto Meter BVA-460, Руководство оператора

Результаты поиска

Содержание BVA-460

Отзывы:

Похожие инструкции для BVA-460

Бренды по названию

Популярные бренды