Auto Meter BVA-460 Скачать руководство пользователя страница 27

Страница: 27 / 30

PRINTING TEST RESULTS

Make sure the Infrared Printer is properly set up by pressing

the "options menu" on the upper right corner of the control

module screen. Choose "Settings". Scroll down to the

bottom of the screen and choose "Print Preference". Choose

appropriate printer preference setting. Press the back around

arrow to return to the Main Menu.

After a test is made with the BVA-460 make sure the results

are displayed on the screen. The results shown will be the

results printed.

Point the BVA-460 in the direction of the Infrared Printer or

Receiver. (1-15 ft.)

Press the <Print> key and the test results will be printed.

After the <Print> key has been pressed, continue to point the

BVA-460 in the direction of the until the print job is complete.

Wait until the printer stops printing before you press the BVA-

460 print key again.

IR Printing Options:

1. PR-12 and AC-14 thermal printers

2. POSI-160 with PR-16 high speed printer.

3. XTC-160 with IR-1 printer interface and PR-16 high speed

printer.

Print Test Results from Email:

1. With an AMPNET Subscription, pressing the AMPNET

button will allow you to email test results to your email

account and print directly from your PC.

Point the BVA-460 in the direction of the printer with the printer’s IR receiver pointed in the

direction of the BVA-460. Press (Print). You should be within 15 ft. of the printer. Wait for the

screen to clear before moving the BVA-460. It takes a moment to send all the test data.

Содержание BVA-460































Результаты поиска

Содержание BVA-460

Отзывы:

Похожие инструкции для BVA-460

Бренды по названию

Популярные бренды

Auto Meter BVA-460, Руководство оператора

Результаты поиска

Содержание BVA-460

Отзывы:

Похожие инструкции для BVA-460

Бренды по названию

Популярные бренды