Auto Crane 6006EH Скачать руководство пользователя страница 87

Страница: 87 / 105

FM CONTROL

USE AND CARE

10-1.0

2/15/05

TRANSMITTER LAYOUT

There is a red light to the left of the

ON/OFF Toggle switch

and a yellow light to the right. As the

battery runs down, the red light will begin to flash as well as the yellow light.

If the yellow light is rapidly flashing this indicates that the unit is transmitting. Refer to the

Transmitter Diagnostics Section for a detailed explanation of each light combination.

In addition to the two lights mentioned above there are four function toggle switches. These

functions from left to right are to be used to raise and lower the boom, raise and lower the hoist

cable, rotate the crane and extend and retract the boom.

POWER ON/OFF TOGGLE SWITCH

The transmitter is powered by 4-AA alkaline batteries, located under the back cover of the

housing. To turn the transmitter on, press and hold the

Power On Toggle

, release once the

transmit light starts blinking. To turn the unit off, press and hold the power off toggle, release

after the transmit light stops flashing.

FUNCTION SWITCHES

To operate a function, toggle one of the function switches with either the thumb of the hand

holding the unit or the thumb or fingers of the opposite hand. More than one function can be

activated at one time.

CARE

KEEP DRY. Do not clean the transmitter / receiver under high pressure. If water or other liquids

get inside the transmitter battery or receiver compartment, immediately dry the unit. Remove the

case and let the unit air dry.

WELDING

DISCONNECT THE RADIO RECEIVER BEFORE WELDING on the crane, load, or truck. Failure

to disconnect will result in the destruction of the radio receiver.

Содержание 6006EH










































































































Результаты поиска

Содержание 6006EH

Отзывы:

Auto Crane 6006EH, Руководство пользователя, Страница: 87 / 105

Результаты поиска

Содержание 6006EH

Отзывы: