Auto Crane 6006EH Скачать руководство пользователя страница 20

Страница: 20 / 105

--- IMPORTANT ---

OPERATION OF UNIT

2-7.0

8/19/05

1. Make sure this manual has been thoroughly

read by all crane operating personnel and

supervisors.

2. A routine inspection of the crane should be

mandatory before each operating day. Any

defects should be corrected immediately.

3. At a job site the vehicle should be positioned so

that the crane can adequately reach the load

within the rated capacity (centerline of rotation

to hoist hook).

4. Keep the vehicle as level as possible during

operation.

5. For electric cranes,

engage emergency brake

and leave ignition on with transmission in

neutral (or in park for automatic transmissions).

Activate any crane power switches. For Auto

Crane units requiring battery and hydraulic

operation,

engage emergency brake,

place

gear selector in neutral, press clutch, activate

PTO, release clutch and after hydraulic fluid is

warm, set throttle control to proper engine

speed.

6. Always use outriggers from the truck to the

ground. Be sure these are firm and adequately

positioned. When rotating,

keep load as low to

the ground as possible.

7. Remove the transmitter from cab or storage

area. Power transmitter on. Detach hook from

dead man. Crane is now ready for operation.

8. Always boom up before rotating so the boom will

clear the required boom support.

9. When extending the boom, always maintain

clearance between the boom crown and the

traveling block or hoist hook.

10. Always observe safe and practical operation to

avoid possible accidents. Refer to Safety Tips

and Precautions.

11.

After completing lifting operations, return the

boom to stowed position on the boom support.

Avoid unneeded pressure on the boom support.

12. Store transmitter in proper location (in cab or

storage area).

13. Return outriggers to stowed position. Make sure

they are pinned in place or jacklegs are returned

to compartment.

14. Check work area for any tools or equipment not

stored.

15.

Release throttle control, depress clutch and

disengage PTO. Deactivate any crane power

switches.

16.

Report any unusual occurrence during crane

operation that may indicate required maintenance

or repair.

17.

NEVER

use two cranes to support a load too

large for either crane.

OPERATION OF

OUTRIGGERS

HYDRAULIC OUTRIGGERS

1. Shift crane/outrigger control valve to

"outrigger" position.

2. Operate the outrigger control valves to

position the outriggers.

3. After outriggers are positioned, return

crane/outrigger selector to "crane"

position.

4. Crane is now ready to operate.

MANUAL OUTRIGGERS

1. Pull lock pins to release jackleg or drop

down outrigger and move to outermost

lock position.

2. Make sure lock pins are reinstalled

properly.

3. Lower outrigger pad to firm ground and

adjust foot to take out slack.

4. Crane is now ready to operate.

Содержание 6006EH










































































































Результаты поиска

Содержание 6006EH

Отзывы:

Auto Crane 6006EH, Руководство пользователя, Страница: 20 / 105

Результаты поиска

Содержание 6006EH

Отзывы: