manualshive.com logo in svg

Autel EU908, Руководство пользователя, Страница: 20 / 100

Поделиться
Скачать
Autel EU908 Скачать руководство пользователя страница 20

 

17 

 

If retrieved DTCs contain any manufacturer specific or enhanced codes, 
a 

“Manufacturer  specific  codes  are  found!  Press  any  key  to  select 

vehicle  make!

”  message  comes  up  prompting  you  to  select  vehicle 

manufacturer to view DTC definitions. Use 

UP/DOWN

 scroll button to 

select manufacturer and then press 

OK

 button to confirm.   

 

If the manufacturer of your vehicle is not listed, use the 

UP/DOWN

 scroll 

button to select 

Other

 and press the 

OK

 button.   

Erase Codes 

CAUTION:

 

Erasing the Diagnostic Trouble Codes may allow the scan tool 

to delete not only the codes from the vehicle’s on-board computer, but also 
“Freeze Frame” data and manufacturer specific enhanced data. Further, the 
I/M Readiness Monitor Status for all vehicle monitors is reset to Not Ready 
or Not Complete status. Do not erase the codes before the system has been 
checked completely by a technician.   

NOTE 

Erasing  codes  does  not  mean  that  trouble  codes  in  ECU  have  been 
eliminated completely. As long as there is fault with the vehicle, the trouble 
codes keeps on presenting.

   

 

This function is performed with key on engine off (KOEO). Do not start 
the engine. 

1)  Use  the 

UP/DOWN

  scroll  buttons  to  select 

Erase  Codes

  from 

Diagnostics

 

Menu

 and press the 

OK

 button.   

2)  A warning message comes up asking for your confirmation.   

 

If you do not want to proceed with erasing codes, press 

ESC

 button 

or select 

NO

 to exit and return to previous screen. 

3)  Press the

 OK

 button to confirm. 

 

If  the  codes  are  cleared  successfully,  an  “Erase  Done!” 
confirmation message shows on the display. 

 

 

If the codes are not cleared, then an 

“Erase Failure. Turn Key on 

with Engine off!

” message appears.   

4)  Press any button to return to 

Diagnostic Menu

. 

Live Data 

In this function, you can not only read the live data but also record data for 
later review. 

Содержание EU908





































































































Отзывы:

Нет отзывов