Autel EU908 Скачать руководство пользователя страница 19

Страница: 19 / 100

Figure 3-1



If more than one module is detected, you will be prompted to select a
module before testing.



Use the

UP/DOWN

scroll button to select a module and press the

button.

Read Codes



Reading Codes can be done with the key on engine off (KOEO) or with
the key on engine running (KOER).

1) Use

UP/DOWN

scroll button to select

Read Codes

from

Diagnostic

Menu

and press

button.

Figure 3-2

2) Use the

UP/DOWN

scroll button to select

Stored Codes

Pending

Codes

from the

Read Codes

menu and press the

button.



If there is not any Diagnostic Trouble Code, the display indicates

“

(pending) codes are stored in the module!

” Wait a few seconds or

press any key to return to previous screen.

NOTE

Permanent Codes is available for vehicles supporting the CAN protocols.

2) View DTCs and their definitions on screen.

3) If more than one DTC is found, use the

UP/DOWN

scroll button to check

all the codes.

Diagnostic Menu
1. System Status

2. Read Codes
3. Erase Codes
4. Live Data
5. Freeze Frame
6. I/M Readiness
7. O2 Monitor Test

8.On-Board Monitor Test

System Status

MIL Status

OFF

Codes Found

Monitors N/A

Monitors OK

Monitors INC

Save OK

Содержание EU908





































































































Результаты поиска

Содержание EU908

Отзывы:

Autel EU908, Руководство пользователя, Страница: 19 / 100

Результаты поиска

Содержание EU908

Отзывы: