background image

Original instructions

Air series

Part C: LK6 and LK8 transmitting units

index

1 description 

 ............................................................................................................  2

Technical data  .......................................................................................................  3

Technical data sheet  .............................................................................................  3

4 Plates 

 .....................................................................................................................  4

4.1  Plates on LK6 and LK8 units in a radio remote control  .....................................  4

Light signals  ..........................................................................................................  5

General operating instructions  ............................................................................  7

6.1  Starting up the radio remote control  .................................................................  7

6.2  Command activation  ........................................................................................  9

6.3  Data Feedback Function  ..................................................................................  9

6.4  Radio link interruption  ......................................................................................  9

6.5  Transmitting unit automatic switch off 

 ..............................................................  9

6.6  Switching off the transmitting unit 

...................................................................  10

7 Operation 

 .............................................................................................................  10

7.1 Battery  ...........................................................................................................  10

7.2  ID internal tx memory  .....................................................................................  11

7.3  Power keyswitch  ............................................................................................  11

7.4  START pushbutton  ........................................................................................  13

7.5  FUNCTION pushbutton  ..................................................................................  13

7.6  STOP pushbutton  ..........................................................................................  13

Malfunction signalled by the transmitting unit  .................................................  14

AUTEC

LILK6E00-01

Содержание Air LK6

















Отзывы: