austriamicrosystems AS5046 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 21

austriamicrosystems AS5046 Скачать руководство пользователя страница 5

AS5046 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER
Demoboard Operation Manual

Revision 1.1, 3-Jun-08 www.austriamicrosystems.com

Page 5 of 21

3.2.2

Hardware Driver Installation

Step 2/3: Installing the USB Controller

Connect the demoboard to a free USB slot on your PC. Your Windows® software

will automatically detect the USB controller on the demoboard:

When prompted for an installation file, refer to the file "ezusbw2k.inf" that was extracted during the demoboard software

installation (step 1) in the directory of your choice

(default C:\program files\austriamicrosystems AG\AS5046_DemoBoardSW_x.x).

After completing the installation, you should get this or a similar message (depends on platform):

Click on "finish".

3.2.3

Step 3/3: Reboot

Reboot your PC if requested by the operating system.

«
...
3
4
5
6
7
...
»

Содержание AS5046






















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды