austriamicrosystems AS5046 Скачать руководство пользователя страница 21

AS5046 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER  
Demoboard Operation Manual

 

Revision 1.1, 3-Jun-08                                                     www.austriamicrosystems.com   

Page 21 of 21 

8

 

Revision History 

Revision 

Date 

Description 

 

1.0 22-Mai-2007

 

Initial Creation 

 

 

 

 

 

 

9

 

Contact 

Headquarters 

austriamicrosystems AG 

A 8141 Schloss Premstätten, Austria 

Phone:  +43 3136 500 0 

Fax: 

+43 3136 525 01 

[email protected]

 

www.austriamicrosystems.com 

 

10

 

Copyright 

Devices sold by austriamicrosystems are covered by the warranty and patent indemnification provisions appearing in its 

Term of Sale. austriamicrosystems makes no warranty, express, statutory, implied, or by description regarding the 

information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems 

reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this 
product into a system, it is necessary to check with austriamicrosystems for current information. This product is intended for 

use in normal commercial applications. 

 

Copyright © 2007 austriamicrosystems. Trademarks registered ®. All rights reserved. The material herein may not be 
reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. To the 

best of its knowledge, austriamicrosystems asserts that the information contained in this publication is accurate and correct. 

However, austriamicrosystems shall not be liable to recipient or any third party for any damages, including but not limited to 

personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or 
consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical 

data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems rendering of 

technical or other services.  

 
 

 

 

 

a leap ahead 

 

Содержание AS5046






















Отзывы: