YL-240 4500KG BASE PLATE CAR HOIST
Installation and operation manual
6
1. Carefully remove the crating and packing materials.
CAUTION!
Be
careful when cutting steelbanding material as items may become
loose and fall causing personal harm or injury.
2. Check the voltage, phase and proper amperage requirements for
the motor shown on the motor plate. Wiring should be performed
only by a certified electrician.
1. Read and understand all instructions and all safety warnings
before operating lift.
2. Care must be taken as burns can occur from touching hot parts.
3. Do not operate equipment with a damaged cord or if the equipment
has been dropped or damaged until it has been examined by a
qualified service person.
4. Do not let a cord hang over the edge of the table, bench, or counter
or come in contact with hot manifolds or moving fan blades.
5. If an extension cord is necessary, a cord with a current rating equal
to or more than that of the equipment should be used. Cords rated
for less current than the equipment may overheat. Care should
be taken to arrange the cord so that it will not be tripped over or
pulled.
6. Always unplug equipment from electrical outlet when not in use.
Never use the cord to pull the plug from the outlet. Grasp plug and
pull to disconnect.
7. Let equipment cool completely before putting away. Loop cord
loosely around equipment when storing.
8. T o reduce the risk of fire, do not operate equipment in the vicinity
of open containers of flammable liquids (gasoline).
9. Adequate ventilation should be provided when working on
operating internal combustion engines.
10. Keep hair, loose clothing, fingers, and all parts of body away
from moving parts. Keep feet clear of lift when lowering.
Avoid pinch points.
11. DANGER! To reduce the risk of electric shock, do not use on
wet surfaces or expose to rain. The power unit used on this lift
contains high voltage. Disconnect power at the receptacle or
at the circuit breaker switch before performing any electrical
repairs. Secure plug so that it cannot be accidentally plugged in
during service, or mark circuit breaker switch so that it cannot be
accidentally switched on during service.
12. Use only as described in this manual. Use only manufacturer’s
recommended attachments.
13. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses only have
impact resistant lenses, they are not safety glasses.
14. Consider work environment. Keep work area clean. Cluttered
work areas invite injuries. Keep areas well lit.
15. Guard against electric shock. This lift must be grounded while in
use to protect operator from electric shock. Never connect the
green power cord wire to a live terminal. This is for ground only.
16. Only trained operators should operate this lift. All non-trained
personnel should be kept away from the work area. Never let
non-trained personnel come in contact with or operate lift.
17. DO NOT override self-closing lift controls.
18. Clear area if vehicle is in danger of falling.
19. ALWAYS make sure the safeties are engaged before attempting to
work on or near a vehicle.
21. WARNING! RISK OF EXPLOSION. This equipment has internal
arcing or sparking parts which should not be exposed to
flammable vapors. This machine should not be located in a
recessed area or below floor level.
22. MAINTAIN WITH CARE. Keep lift clean for better and safer
performance. Follow manual for proper lubrication and
maintenance instructions. Keep control handles and/or buttons
dry, clean and free from grease and oil.
23. Check for damaged parts. Check for alignment of moving parts,
breakage of parts or any condition that may affect operation of
lift. Do not use lift if any component is broken or damaged.
24. NEVER remove safety related components from the lift. Do not
use lift if safety related components are missing or damaged.
23. STAY ALERT. Use common sense and watch what you are doing.
Remember, SAFETY FIRST.
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Read these safety instructions entirely
Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures. Never attempt to lift
components without proper lifting tools such as forklift or cranes. Stay clear of any moving parts that can fall and cause injury.
PH 1300 232 153
HIGHLIFT
