background image

12    |

Aussie Eco-Clean Super Indy Operating & Maintenance Manual - 

2020

FIG.12

REGULATING  PRESSURE 

AND USING STEAM

(If available)

This  chapter  concerns  only 

those  models  provided  with 

the  “pressure  regulating”  de-

vice. The pressure regulator, 

fig. 12, allows the operator to 

adjust  the  working  pressure.  

When  knob  C  is  turned  in 

an  anti-clockwise  direction 

(B) (minimum),  the  working

pressure is reduced.

ADVICE ON USING DETERGENTS

 

This cleaner has been designed for use with the detergents 

supplied or recommended by the manufacturer.

The use of other detergents or chemicals may influence the 

safety of the cleaner.

1

For environmental compatibility

, we recommend a rea-

sonable use of detergents, according to the instructions 

on the pack.

2

From the range of recommended products, choose the

one most suited to the washing job to be done and dilute 

it with water according to the instructions on the pack or 

in the catalogue of the detergents most suited for the 

type of hot or cold water cleaner.

3

Ask your dealer for the detergents catalogue.

 

During use with boiling water, "Steam Phase", keep 

away from the openings for fumes discharge (risk of bur-

ning).

When  you  have  finished  using  the  "Steam  Phase",  turn 

the  thermostat  knob  "B"  to  position  "0"  (fig.  7)  and  let 

the machine cool down for about 3 minutes with the gun 

turned on.

OPERATING  PHASES  FOR  CORRECT  CLEANING  WITH 

DETERGENTS 

1

) Prepare  the  solution  of  detergent  at  the  concentration

most suitable for the type of dirt and the surface that is to be 

washed. 

2

) Start the cleaner, turn on the detergent tap (if present), switch

on the detergent suction control on the lance and spray the dirty 

surface with the diluted product, working from bottom to top. 

Let it react for a few minutes.

3

) Rinse the whole surface well from top to bottom with hot or

cold water at high pressure. 

4

) After using with detergent, flush out the inlet; place the de

-

tergent suction hose (fig. 9) in a tank of clean water and let the 

pump run for 1 minute with the dosing tap turned fully on and 

the lance in detergent delivery condition.

MAINTENANCE

ONLY THE OPERATIONS AUTHORIZED IN THIS IN-

STRUCTIONS MANUAL MAY BE CARRIED OUT BY THE 

USER.

ALL OTHER OPERATIONS ARE FORBIDDEN.

For maintenance of the boiler, high pressure pump, the 

electrical parts and all parts with a safety function, you must 

apply to our Technical service centre.

 

Disconnect the water cleaner from the mains electricity 

supply via the omnipolar switch or by unplugging the plug from 

the socket and close the water supply tap (see chapters on 

connecting to the electricity and water mains

)

 

before carrying 

out  any  maintenance  jobs.    Once  maintenance  has  been 

completed, ensure that the closing panels have been correctly 

reassembled and anchored with the screws provided before 

reconnecting the cleaner to the mains.

Failure to do so may cause a risk of electric shock.

PRECAUTIONS   AGAINST  FROST

The cleaner must not be exposed to frost.

  

If the cleaner is left in premises where it is exposed to frost, 

when work is over or for storage, antifreeze must be used to 

prevent serious damage to the hydraulic circuit. 

!

!

!

Use the steam nozzle (supplied as an accessory).

Turn the thermostat knob “B” (fig. 7) to steam position to obtain 

an increase in the temperature of the water at delivery.

At  work  temperatures  higher  than  95°C  (203°F),  the  work 

pressure must be < 32 bar (460 PSI).

Содержание Eco Clean Super Indy





















Отзывы: