AUSA C300H Скачать руководство пользователя страница 54

Страница: 54 / 140

C300H / C300HI / C300H x4 / C300HI x4
C350H / C350HI / C350H x4 / C350HI x4

Decals / labels / identification plates all markets (USA Market)

STICKER:

JOYSTICK FUNCTION BUTTONS

REFERENCE:

DESCRIPTION:

QUANTITY:

10.15011.00

INDICATIVE STICKER 4WD CONNECTION (



)

POSITION:

Stuck on the inside of the right front fender, in the top center position. Just above
sticker ref. 10.15005.01 o 10.15009.00, at 0.1969 in.

STICKER:

DANGEROUS AREA.. SUBSTITUTE REF. 45.01352.00

REFERENCE:

DESCRIPTION:

QUANTITY:

45.01352.01

INDICATIVE STICKER

POSITION:

On both sides of the mast, above the beam, with its upper side aligned at 4ft 92
in from the ground, below the sticker ref. 13.12136.00 “AUSA Make”, and 0.3937
in away from it.

STICKER:

TO HOIST MACHINE

REFERENCE:

DESCRIPTION:

QUANTITY:

58.01353.01

INDICATIVE STICKER 105X100

POSITION:

On the left side of the machine, at the lower exterior part of the front fender,
aligned on its upper side with sticker 45.19101.00 “EC mark”.

Содержание C300H













































































































































Результаты поиска

Содержание C300H

Отзывы:

Бренды по названию

Популярные бренды

AUSA C300H, Руководство оператора

Результаты поиска

Содержание C300H

Отзывы:

Бренды по названию

Популярные бренды