Aurora AGI6500DE Скачать руководство пользователя | Manualshive

Страница: 32 / 44

background image

Engine & Alternator Resilient Mounts Replacement.

Cylinder Head Nuts Tightening.

1. Clean fuel injector sleeve surface in cylinder head.
2. Install new gasket, spacer, and fuel injector in cylinder head. Ensure fuel injector is

positioned to connect pressure fuel line prior to securing in cylinder head.

3. Secure fuel injector in cylinder head with retainer and nuts. Torque nuts evenly to 7-9

lbs-ft (9-12 Nm).

4. Connect pressure and return fuel lines. Bleed fuel system if necessary, Install gasket

and valve cover on cylinder head with bolts.

5. Tighten fuel line connecting nut and bleed fuel system if necessary

Intake and Exhaust Valve Adjustment.

Perform valve adjustment when engine is cold. Procedure is the same for intake and
exhaust valve.

1. Remove bolts securing valve cover. Then remove valve cover with gasket.
2. Remove cooling fan cover, refer to paragraph 4.53.b.
3. Align T mark on flywheel with V notch on cylinder body fin

This video shows the above procedure.

http://www.youtube.com/watch?v=J64VghmSsBc&

Ensure both valves are fully closed (both rocker arms have free play).

4. Loosen nut for adjusting screw and adjust screw until correct clearance [0.006 in.

(0.15 mm)] is achieved between rocker arm and valve cap

AGI6500DE & AGI6500SDE Operator / Owners Manual Version 11.4.1

Page 32

«
...
30
31
32
33
34
...
»

Содержание AGI6500DE













































Отзывы:

Нет отзывов

Похожие инструкции для AGI6500DE

Бренд: MCP Страницы: 4

Бренд: RINCO ULTRASONICS AG Страницы: 54

Бренд: Panacom Страницы: 10

Бренд: Roberts Страницы: 12

Бренд: Logic Страницы: 36

Бренд: Feider Machines Страницы: 78

Бренд: Wallenstein Страницы: 41

Бренд: Champion Страницы: 29

Бренд: Shindaiwa Страницы: 54

HW5500 - 5500 Portable Generator

Бренд: Honeywell Страницы: 100

Бренд: Greenlee Страницы: 22

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 4

Бренд: Philips Страницы: 7

Бренд: Philips Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды