Aurora AGI6500DE Скачать руководство пользователя | Manualshive

Страница: 28 / 44

background image

Air Filter Element Replacement.

Removal

1. Shut down the generator set
2. Remove 4 nuts securing metal cover on the silent diesel generator to expose the

air filter assembly inside the enclosure.

  3.  Remove the wing nut
  4.  Remove the pre filter element
  5.  Remove the paper element
  6.  If necessary, remove gaskets from mounting plate and cover. Clean adhesive

residue from surfaces

Inspecting and Cleaning

1. Inspect cover for cleanliness, cracks and other damage. Clean cover with mild

soap and water.

  2.  Inspect filter element for cleanliness, dents, and crushed corrugations
  3.  Replace damaged parts.
  4.  Replace filter element if dirty
  5.  Replace pre-filter.

Installation

  1.  If removed, install new gaskets on mounting plate and cover
  2.  Soak new pre-filter in clean engine oil and squeeze out ALL
  3.  Install pre-filter over filter element. Pre-filter should fit snugly over filter element
  4.  Position filter element with pre-filter and cover on mounting plate
  5.  Install wing nut.

AGI6500DE & AGI6500SDE Operator / Owners Manual Version 11.4.1

Page 28

«
...
26
27
28
29
30
...
»

Содержание AGI6500DE













































Отзывы:

Нет отзывов

Похожие инструкции для AGI6500DE

Бренд: Mase Generators Страницы: 92

Бренд: Generac Portable Products Страницы: 36

UT905000SA Series

Бренд: Homelite Страницы: 64

Бренд: Agilent Technologies Страницы: 78

Бренд: Garland Страницы: 120

PS906800 Series

Бренд: Power Stroke Страницы: 72

Бренд: ZIPPER MASCHINEN Страницы: 39

Бренд: Uniden Страницы: 14

ElectroMate VEC097

Бренд: Vector Страницы: 20

Бренд: Curtis Страницы: 1

HW5500 - 5500 Portable Generator

Бренд: Honeywell Страницы: 100

Бренд: HP Страницы: 36

Бренд: HP Страницы: 9

Бренд: HP Страницы: 116

Бренд: HP Страницы: 118

Бренд: HP Страницы: 406

Бренд: Kenwood Страницы: 2

Бренд: Philips Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды