Aurora AGI6500DE Скачать руководство пользователя

Страница: 24 / 44

PREVENTIVE MAINTENANCE

CHECKS AND SERVICES

Within designated intervals, these checks are to be performed in the order listed.

M-Monthly Q-Quarterly S-Semi-annually A-Annually B-Bi-annually H-Hourly

Item

Interval

Item To Be

Inspected

Procedure

Generator should

not be used if

Item

Item To Be

Inspected

Procedure

Generator should

not be used if

Diesel Engine

Check for loose, damaged, or

missing parts. Tighten loose

parts. Repair or replace damaged

or missing parts. Inspect

decompression lever for debris.

Clean if needed.

Engine parts are

loose, damaged,

or missing.

Starter

Battery

Check battery terminals are

secure. Recharge battery if not

in use.

Primary and

Pre-filter Air

Filter

Elements

Inspect for clogged primary

(paper) air filter element. Clean

every 50 hours or as required, or

replace element if damaged.

Replace pre-filter (foam) element.

Air cleaner

element is

clogged or

damaged.

Ground

Terminal Lug

Check for damage or corrosion.

Control Panel

Check for any loose hardware or

corrosion.

(1st

Time)

100

Engine Lube

System

Change diesel engine oil after the

first 20 hours of operation and

then after every 100 hours. (1)

Remove diesel engine oil drain

plug and collect oil in an

appropriate chemical resistant

container for disposition/disposal.

Remove, clean, and install oil

strainer. Add proper lube oil.

15W40 Synthetic

100

Fuel Filter

Element

Replace fuel filter element.

Inspect gaskets for damage

Spark Arrestor

Check for damaged, missing or

corroded spark arrestor if

present.

1000

Alternator

Brushes

Wires and

Holders

Check for worn alternator

brushes. Length must be a

minimum of 0.5 in. (1.3 cm).

Check for damaged or missing

brush caps, wires, and holders.

Alternator

brushes worn.

Damaged or

missing brush

caps, wires, and

holders

AGI6500DE & AGI6500SDE Operator / Owners Manual Version 11.4.1

Page 24

Содержание AGI6500DE













































Результаты поиска

Содержание AGI6500DE

Отзывы:

Похожие инструкции для AGI6500DE

Бренды по названию

Популярные бренды

Aurora AGI6500DE, Руководство по эксплуатации

Результаты поиска

Содержание AGI6500DE

Отзывы:

Похожие инструкции для AGI6500DE

Бренды по названию

Популярные бренды