manualshive.com logo in svg

Aurora Design SCRF, Руководство пользователя и техническое руководство

Поделиться
Скачать
Aurora Design SCRF Скачать руководство пользователя страница 5

to set the modulation depth of the audio RF carrier to suite the source level. Please 
refer to 

Specifications

 sections found later in this manual.

Status LED:

The status LED conveys the current operating state of the converter. 
 

Slow Flashing:

No video input signal detected. Default image will be output.

Solid:

Converter locked to video input. Normal operation.

Pulsating: 

Converter in low power Sleep mode.

Fast Flashing: 

Converter storing default image to internal FLASH

Audio Level:

The Audio Level control is used to set the modulation depth of the audio RF 

carrier. This control is required to handle the variations in the audio output levels 
from different devices. This control should be set to the maximum possible without 
causing distortion of the audio in the RF signal. The potentiometer is adjusted by 
inserting a small flat blade or phillips screw driver into the hole, and turning it until it 
engages the rotor of the potentiometer. Maximum drive is obtained by turning the 
potentiometer clockwise.

Rear Panel

The rear panel is shown below:
 

Composite
     Video
    Output

      User
Pushbutton

    RF
Output

 9Vdc
 Input

RF Channel
    Select

                                                                                                              

Introduction

5

Содержание SCRF


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды