background image

 
 

 

 

 

 

 

 

 

AUMSHIVAY ENGINEERING PRIVATE LIMITED 

 

 

B-21, Bhan Nagar, Queens Road, Jaipur-302021

 

Website: www.aumshivay.com, www.omengineering.in

 

E-mail:[email protected]

 

 

 

 

 

 

 

 

 

 

PAGE. 4

 

 

REG. OFFICE:VILLA NO. 60,LATA NAGAR, KALWAR ROAD, JHOTWARA, JAIPUR - 302012 

TM 

 

TM 

 

  

GENERATOR

 

PROTECTION RELAY 

 

 

 

 

GENERATOR  PROTECTION  RELAY  (MG30  &  MG30-I);

 

These  are

 

Multifunction  Microprocessor  Relay  for 

protection of medium/ large synchronous generators. The relay measures the RMS of three-phase currents and voltages and 

computes  the  positive  and  negative  sequence  components  of  the  Current  system.  A  separate  input  is  dedicated  to  the 

measurement  of  the  Neutral-to-Ground  voltage  and  its  harmonic  components  used  for  a  complete  Stator  Ground  Fault 

protection. MG30 incorporates 5 output relays expandable up to 16 with the additional module REX-8. 

 

 
Features;

 

 

Voltage-controlled over-current protection. 

 

Thermal image element with pre-alarm level. 

 

Reverse power protection. 

 

Loss of Field protection. 

 

PT s' fuse failure protection    

 

Modbus Communication Protocol  

 

Breaker Failure protection 

 

Inadvertent C/B closure protection 

 

Blocking Output and Blocking Input for pilot wire selectivity coordination. 

GENERATOR PROTECTION RELAY (MG30 & MG30-I)

 

Item 

Generator Protection Relay  

Make 

L&T 

Model 

MG30 & MG30-I 

Generator Type 

MG30:

 For Impedance Grounded (NGR / NGT) 

Generators.                                                                                    

Applications 

MG30 / is Multifunction Microprocessor Relay for 
protection of medium/large synchronous 
generators. The relay measures the RMS of three-
phase currents and voltages and computes the 

positive and negative sequence components of the 
Current system. 

Содержание MC 12A



















Отзывы: