AUMA SAI 07.2 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

AUMA SAI 07.2 Скачать руководство пользователя страница 19

Type of current, mains voltage and mains frequency must match the data on the
motor name plate.

Connecting cables

●

For device insulation, appropriate (voltage-proof) cables must be used. Specify
cables for the highest occurring rated voltage.

●

Use connecting cable with appropriate minimum rated temperature.

●

For connecting cables exposed to UV radiation (outdoor installation), use UV
resistant cables.

5.2.

SH/SB electrical connection (AUMA plug/socket connector)

Figure 15: SH and SB electrical connection

[1]

Cover

[2]

Socket carrier with screw-type terminals

With crimp-type connection as an option

[3]

DS intermediate frame with pin carrier

[4]

Actuator housing

[5]

DBE resistant cable entries

(available as option for SB version)

Short description

Plug-in electrical connection with screw-type terminals for power and control contacts.
Control contacts also available as crimp-type connection as an option.

SH version (enlarged AUMA plug/socket connector). SH version (enlarged AUMA
plug/socket connector with two mounting bases). SB available as option with DBE
resistant cable entries. For cable connections in SH version, remove the AUMA
plug/socket connector and the socket carrier from cover. For SB version with DBE
resistant cable entries, the cables are connected to these cable entries.

19

SAI 07.2 – SAI 16.2 / SARI 07.2 – SARI 16.2
for use in nuclear power plants

Electrical connection

«
...
17
18
19
20
21
...
»

Содержание SAI 07.2





















































Отзывы:

Нет отзывов