AUMA EPAC Скачать руководство пользователя страница 9

Страница: 9 / 49

PVST Failure :

This failure occurs when the PVST command doesn’t take place after a specified time

(that is specific to actuators based on its RPM and No. of Turns). This failure is indicated by using
any one of the programmable relays present in your module.

2.7

INHIBIT OPTION

Inhibit is an interlock for open close operations. Inhibit Operation can be Enabled or Disabled in

Software (Program Mode). In this module, separate terminals for Inhibit Open and Inhibit Close are

available. Based on this, Open/Close Commands can be inhibited.

2.8

REMOTE SELECTOR SWITCH

This option allows the user to create a selector switch for the actuator in Remote mode. It is mainly

used to lock/unlock the Local operation of the actuator using push buttons through a Remote

command. This is serves as a software lock.

2.9

LOCAL CONTROL STATION (LCS) PRIORITY

When this feature is enabled, the user can control the actuator in remote 4 –wire mode of operation

even when in 4-20mA or MODBUS mode of Operation.

2.10

REMOTE LOCAL STOP

This option is also software configurable and can be enabled in Program Mode. The

actuator

should stop running in Remote Mode when STOP key is pressed in the Actuator Front Panel. No

commands should be accepted by the actuator until it is reset.

2.11

TIMER MODE

Timer mode is used to control the valve movement. This mode allows us to open or close the valve

slowly towards the end position after reaching a certain distance with continuous operation.

Configurable Options



Open timer start Valve Position: The user has to set the valve position at which this Timer

mode should go on for Open Command.



Open ON time : This parameter decides the amount of time (in s) the actuator runs in Open

direction before shutting off for Open OFF time (in s). This continues to happen until the

respective limit switch is hit (unless the switch is bypassed).



Open OFF time: This parameter decides the amount of time (in s) the actuator shuts off

before running in open direction for Open ON time (in s). This continues to happen until the

respective limit switch is hit (unless the switch is bypassed).

Содержание EPAC


















































Результаты поиска

Содержание EPAC

Отзывы:

Похожие инструкции для EPAC

Бренды по названию

Популярные бренды

AUMA EPAC, Руководство по эксплуатации и инструкция

Результаты поиска

Содержание EPAC

Отзывы:

Похожие инструкции для EPAC

Бренды по названию

Популярные бренды