auer 955000, Инструкция по установке и эксплуатации

Страница: 3 / 28

-
MANUAL
HTi
70
6 & 8 KW HEAT PUMPS
- 3
1-SAFETY
Danger resulting from improper qualifi cations
• Any work carried out by an unqualifi ed
person can result in damage to the
installation or in physical injury.
• Do not perform maintenance on this appliance
unless you are a qualifi ed professional.
• If the appliance is malfunctioning or not
working, cut the electricicty supply to the
electrical components and seek advice from a
qualifi ed professional.
Danger resulting from improper use
This appliance should not be used by anyone
(including children under the age of 8 years
old)with reduced physical, sensory or mental
capabilities, or by an yone with insuffi cient
experience or knowledge of the appliance;
unless they are being supervised by someone
who is responsible for their safety and in
possession of the operating instructions of the
appliance, or if they have been instructed in
the proper use and in the risks of operating the
appliance.
Children must not play with the appliance.
Cleaning and maintenance of the appliance
must not be undertaken by children without
supervision.
Applicable areas of use
The appliance is intended for use an appliance
for the production of domestic hot water: it
must be connected to a heating installation,
and while complying with the instructions,
connected to the drinking water network.
The intended use of the appliance includes the
following points:
• Following the instructions for operating,
installing and maintaining this appliance and
all of its components.
• Ensuring the compliance of the appliance to
all inspection and maintenance conditions
which are listed in this manual.
Danger of death by electrocution
• Touching live electrical wires can cause
severe bodily injury, and lead to death by
electrocution.All installation and maintenance
work must be carried out with the appliance
switched off and by a qualifi ed professional.
Before carrying out any work on the
appliance:
- Cut-off the electricity supply.
- Ensure that there is no possibility of the
power supply becoming active again.
- Wait at least 5 minutes for the capacitors
to lose their charge.
• Do not get water on any of the control or
electrical components. Always disconnect the
appliance from the electricity supply before
carrying out work on any of the electrical
components.
Danger of death if the pressure relief valves
are missing or defective
A defective pressure relief valve may prove
dangerous and could lead to burns or other
injuries by, for example, the pipes bursting.
The information presented in this document does
not contain all of the schematic diagrams needed
for a professional installation of the pressure relief
valves.
• Install the necessary pressure relief valves on
the circuit.
• Inform the user concerning the function and
the placement of the pressure relief valves.
• Respect all applicable national and international
regulations, standards and decrees.
Risk of material damage
The heat pump can only work when fi lled with
water. Never switch on the appliance if it is not
completely fi lled with water and purged of air.
Rules and regulations (decrees, standards,
laws)
Once the appliance is installed and switched
on, all decrees, directives, technical rules, safety
measures and standards, must be respected in
their current version in eff ect.
The electrical supply must conform to all
applicable regulations in the country of
installation, as well as the NFC 15-100 standard.
• A method of disconnection ensuring a complete
cut-off must be installed in the fi xed piping to
conform to installation regulations (do not use
a movable outlet).
• Protect the appliance with a 2-pole circuit
breaker with a minimum contact opening of
3mm and must be grounded.
• The devices for electrical cut-off must remain
accessible.
• Water may drain from the discharge pipe of
the pressure limiting device. This pipe should
be kept open to open air.
• The pressure relief valve is mounted on the
condenser. Ensure that the drainage is properly
oriented to prevent water from leaking onto the
electrical components.
Maintenance - Troubleshooting
Maintenance and cleaning of the pilot must be
carried out at least once a year by a qualifi ed
professional.