4
CAUTION!
Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts
are present, and have been received in good condition. Notify the shipper immediately and retain packing material for
inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and
all packing materials. In the event that the product must be returned to the factory, it is important that the product be
returned in the original factory box and packing. If the device has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. the arising condensation water might damage your device. leave the device
switched off until it has reached room temperature.
When you first connect the unit to the ma
ins socket, display will show the “00:00:00”.
If you can receive a DAB+ signal in your
location, the unit will synchronize to the current local time. After approximate one minute, it will switch to STAND BY mode.
•
Press the ON/STANDBY on the unit or on the remote control to switch the unit to ON mode.
•
Press the ON/STANDBY on the unit or on the remote control to switch the unit back to STANDBY mode.
•
Disconnect the mains plug from the mains socket if you want to switch the unit off completely.
Note:
If the digital radio is not used for 20 minutes, it will automatically enter into standby mode.
Follow the below instructions to switch between CD, DAB, FM, AUX IN, USB & BT input modes.
Press the SOURCE button on the micro system repeatedly to cycle between CD, FM, AUDIO-IN & BT input modes.
Press the relevant button on the remote to select the input mode you require. Press the FM/DAB button to switch to DAB
mode. Press once more to switch to FM mode.
Before switching to the DAB input mode the antenna needs to be extended fully to allow stations to be located during the
initial scan.
When the DAB mode is activated for the first time the unit will perform a scan for available stations. You will see SCANNING..
0 appear on the display until stations are located and then the O will change to the amount of stations found.
When located the first alphanumerical station will begin playback while the other stations are stored.
lf no stations where located during the scan, relocate the unit, extend the antenna fully and read the Performing a DAB
station scan section.
Listening to the stored DAB stations
To listen the DAB stations that have been stored press the
[
]
or
[
]
buttons on the micro system or < TUNE or TUNE >
buttons on the remote control.
Press the UNPAIR/ENTER button on the micro system or ENTER on the remote to switch to the selected station.
To scan for radio stations press and hold either of the < TUNE or TUNE > buttons on the remote or
[
]
or
[
]
buttons on the
micro system for two seconds to scan down or up the frequency band. When a station is found the scan will stop and the
station will begin to play.
To fine tune the frequency press either of the < TUNE or TUNE > buttons on the remote or
[
]
or
[
]
buttons on the micro
system (do not press & hold ), to jump 0.05 MHz up or down.
Alternatively press the SCAN button on the remote to begin scanning up the frequency range. When a station is located
playback will begin automatically.
FM scan modes
Scan modes determine how strong an FM signal needs to be, to be accepted as a potential radio station when scanning.
Press the MENU button on the remote or press and hold the MENU/INFO button on the micro system
When the SCAN SETTING option appears press and hold the ENTER button on the remote or UNPAIR/ENTER on the micro
system. Use the < TUNE or TUNE > buttons on the remote or
[
]
or
[
]
buttons on the micro system to select between
STRONG STATIONS (Strong local stations only) or ALL STATIONS (All available stations). Press ENTER button on the remote or
UNPAIR/ENTER on the micro system to save.
Storing station presets
Follow the below steps to store a tuned station to one of 10 preset locations to allow quick access. Tune to the station you
wish to store as a preset and follow the below instructions. Press and hold the MEMORY button on the remote control. The
display will show SAVE TO P1, where P1 is the selected preset location.
