Audiovox PRESTIGE PLATINUM SS6900 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 24

Audiovox PRESTIGE PLATINUM SS6900 Скачать руководство пользователя страница 20

128-8839

20 of 24

20

METHOD 1

To connect to the key in sensor as shown in method 1:
A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.
B. Cut this wire and connect the ignition cylinder side to chassis ground.
C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .
D. Cut this wire and connect the ignition cylinder side to terminal #30 of a P&B VF45F11 or equivalent relay.
E. Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non

striped) side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit.

F. Connect terminal #86 of the relay to a fused +12 volt constant battery source.
G. Connect terminal #87 of the relay to the Chime Module side of the previously cut wire in step D.
H. Connect terminal #85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B.

Note:

A second 4002 series diode may be required to maintain the integrity of the hood open, shut down

circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non

Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode

(Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an

alarm trigger input, be certain to use the dual diode set up shown under the heading Gray wire

shown earlier in the manual.

«
...
18
19
20
21
22
...
»

Содержание PRESTIGE PLATINUM SS6900

























Отзывы:

Нет отзывов