During playback, every time the PLAY MODE key is pressed, the mode would be
changed to the next one as follows:
NORMAL play -> (
)repeat one -> (
)repeat all -> INTRO -> SHUFFLE
Troubleshooting Guide
Should any problem persists after you have made the following checks, consult your
nearest service facility.
Disc play does not start:-
The LOCK switch of the CD player or the wired remote control( if supplied) is set to
LOCK The disc is inserted upside down or incorrectly. Insert the disc correctly with the
label surface up Dusty or defective disc Dirty or dusty lens. The disc compartment
lid is not closed Moisture condensation -> Leave the unit in a warm place until the
moisture evaporates The AC power adaptor is not plugged into the wall outlet The unit
is not placed on a level surface Weak batteries
No sound from the headsets:-
The headphones/earphone plug is not firmly connected to the PHONES jack Adjust
the VOL control Dirty plug
No sound from the connected speakers:-
Check the connections The amplifier is not turned on
Skipping of sound:-
Dirty or defective disc Dirty lens. Strong vibration
When using with batteries the battery life is short:-
Manganese batteries are used. Use alkaline batteries
Display window shows "
" error message and the unit cannot be operated:-
No disc , dirty disc or scratched disc. The unit will return to full stop mode after approx.30
seconds, or reset the player by pressing "STOP" once and then insert a disc to start
playing.
To delete: When open the CD door including that program will be cancelled.
Notes on the LINE OUT jack
If the CD Player you purchased includes a line cord, you can connect it to the input
terminals of a stereo system for enhanced sound. Adjust the volume control of the
stereo system to a desired level.
Please note the volume control of the CD Player will have no effect on the sound
level when the LINE OUT jack is used for connection.
Do not use the headphones jack for connection to a stereo system as sound may
be distorted.
Specifications
General
Compact disc digital audio system
Digital filter eight-time oversampling
Three-spot optical pick up
Output (at 1KHz 0dB level) Line output (stereo minijack)
Output level 0.4V (Rms) at 47 K
Ω
at 1KHz
Headphones/earphone (stereo minijack)
15 mW + 15 mW at 16
Ω
to 32
Ω
Power requirements
2 size AA (LR6 or SUM-3) alkaline batteries, or DC IN 6V,
350mA power adaptor
Polarity of plug
Dimensions
Approx. 128 x 31 x 137 mm (w/h/d)
Weight
Approx. 205g (not incl. batteries)
Chile:
230V AC 5% 50 Hz
Operating voltage:
UK and Germany:
230V AC 5% 50 Hz
U.S.A., Canada:
120V AC 5% 60 Hz
Singapore,Malaysia & Thailand:
200-240V AC 5% 50 Hz
Japan:
100V AC 5% 50/60Hz
Middle East and Australia:
240V AC 5% 50 Hz
Design and specifications are subject to change without notice.
Note:
This appliance conforms with EEC Directive 87/308/EEC regarding interference
suppression.
Maintenance
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.
CLEANING CD
If the CD skips or will not play, the disc may need to be cleaned. Before playing, wipe the
disc from the centre out with a cleaning cloth. After playing, store the disc in its case.
HANDLING THE DISC
Only touch the CD on the edge to avoid finger prints on its surface. Do not stick paper
or tape nor write anything on the surface.
811-890191-161
Various Playing Modes
Normal Play - Playing the Whole Disc
The CD is played once from beginning to end.
Repeat Playback (Repeat One and Repeat All)
To repeat the same track
Press PLAY MODE during play until "
" appears in
the display window. Select desired track to be played only
once by pressing
or
.
To repeat the whole disc
Press PLAY MODE during play until "
" appears in
the display window.
Intro Play - Playing the First About Ten seconds of All the Selections
1.
Press PLAY MODE during play until
flashes in the
display window.
2.
Press
to begin the INTRO play.
3.
Pressing
again will cease the INTRO play and continue
playback in the NORMAL play mode.
* INTRO play always starts from the first track.
Shuffle Play - Playing the Selections in Random Order
1.
Press Play Mode during play until "SHUFF" flashes in the
display window.
2.
Press
to begin the SHUFFLE play.
* To locate the next track: press
. However, you cannot
locate a previous track even if you keep
pressed.
PROG (Program) Play - Playing the Selections in the Desired Order
1.
Press PROG button until
and "
" flash in the
display window.
2.
Press
or
to select the desired selection.
3.
Press PROG to register track no.4, for example, as the first
selection. The track no. indication will be returned to "00".
4.
Repeat steps 2 and 3 .
5.
Press
, "
" stops flashing and play starts.
NOTES:
* Repeat play and INTRO play can be performed during program play.
* The program is also erased when the disc compartment is opened or the auto power
off function turns the power off.
* If the program mode is exited by means of the STOP key, all the programs would
still remain in memory.
* During the program play, the AMS operates in the programed order.
Program Edition
To check: Press "PROG" lightly during programming before you press
. Each time "PROG" is pressed the track number appears in the
display window.
To change: When checking press either
or
to alter the track number for the
program currently displayed. Press "PROG" to register the
newly selected track into memory.
Digital Anti-Shock System
The Digital Anti-Shock System incorporates a special electronic circuit that prevents
sound from skipping when the unit is subjected to shocks and vibration during play.
When you start playback, the Anti-Shock System turn on and "
" indicator
appears in the display to prevent sound skipping.
When the unit receives a physical shock which prevents the laser pick-up from
"reading" the CD, this system immediately starts playing the sound stored in its
memory and continues until the laser pick-up recovers.
If the unit is subjected to continuous shocks and all the data stored in memory is used
up the sound will skip.
If the vibration stops then the data memory will be restored. If continuous vibration is
applied when the data memory is empty, an error message "
" will be displayed. To
reset the CD player press " STOP / POWER OFF " once.
To cancel the Anti-Shock System, press the
ANTI-SHOCK
button, then "
"
indicator disappears in the display.
NOTES:
In the "
DIGITAL ANTI-SHOCK SYSTEM
", battery power consumption is more
because the disc rotates faster than normal and the memory circuit is active.
When the Digital Anti-Shock System is switched on or off, the sound will be interrupted
for a short time. This is normal.
Under some conditions, noise may be heard or sound skipping may occur.
-when the disc is dirty or scratched.
-when the disc contains certain signals.
-when the unit is subjected to a certain kind of shock.
In these conditions, try to release "
DIGITAL ANTI-SHOCK SYSTEM."
Printed in China
All manuals and user guides at all-guides.com