Page 7
TT-2930 - High-torque Professinal turntable system
English
6 - Operating
1
- Turn the power dial to turn on and the speed indicator
and the strobe-illuminator will light up.
2
- Turn on and raise the target light for illumination the
stylus tip by pushing the target light button.
3
- Place a record on the turntable mat. When playing a
45rpm record with a large center hole; place the 45-rpm
adapter on the center spindle.
4
- Set the rotation speed (33/45/78) to match the record.
5
- Release the arm clamp.
6
- Set the cueing lever to the up position.
7
- Press the Start/Stop button and the turntable platter
will start to rotate.
8
- Move the tone arm over the desired groove.
9
- Set the cueing lever to the down position, the tone arm
will descend slowly onto. The record and play begins.
10
- Set the desired pitch adjusts range by depressing
the Quartz buttons until the desired pitch is reached.
Options are +/-10% or +/-20%
11
- Adjust the pitch to a desirable speed. During play,
observe the strobe dots. If the strobe dots appear to the
right, the pitch is slower than the rated speed. If they flow
to the left, the pitch is faster than the rated speed.
If the strobe dots appear stationary, which means the
platter is in normal turntable speed, move the pitch
control slider up or down to adjust the speed.
12
- To suspend play, lift tone arm with cueing lever.
13
- When play is finished, raise the cueing lever, move
the tone arm to the armrest and secure the tone arm with
the arm clamp.
14
- Turn the target light off by pushing the light back
down.
15
- Press the Start/Stop button to stop the platter
rotating.
16
- Turn the power dial to turn off the power.
1
- Remove the main unit with the packing from the box
and take off the packing.
2
- Set the 45rpm adaptor on the main unit.
3
- Insert the turntable platter onto the centre spindle.
4
- Set the slip mat on the platter.
5
- Installation of cartridge:
When installing a cartridge, refer to the operating
instructions of that cartridge. During installation, attach
the stylus protector to guard the stylus tip from damage.
(
a
) Connect the lead wires to the cartridge terminals. The
terminals of cartridge are colour coded.
Connect each lead wire to the terminal of the same
colour.
White (L+) Left c
Blue (L -) Left channel –
Red (R+) Right c
Green (R-) Right channel –
(
b
) Install the cartridge to the headshell and tighten it
with screws provided with the cartridge.
6
- Insert the headshell into the front end of the tonearm,
then turn the lock nut clockwise with the headshell firmly
held horizontally.
7
- Slide counterweight onto tonearm.
Twist it lightly and it will screw onto the rear shaft of the
tonearm.
5 - Assembly
8
- Adjustment of horizontal zero (0) balance and stylus
pressure:
(
a
) Remove the stylus protector, do not touch the stylus
tip during the adjustment.
(
b
) Set the cueing lever to the lower position.
(
c
) Release the arm clamp and lift the tonearm from the
arm rest to free it.
(
d
) Rotate the counterweight until the tonearm is
approximately balanced horizontally (floats freely).
(
e
) Refasten the tonearm with the arm clamp.
(
f
) Hold the counterweight stationary with one hand and
rotate only the stylus-pressure ring to bring the number
"0" of the ring into alignment with the centre line on the
tonearm rear shaft.
(
g
) Rotate the counterweight clockwise until the scale
shows the value corresponding to the pressure of the
used stylus. The stylus pressure of the installed pick-up
system is 2 g. If you use a separate pick-up system,
please follow the manufacturer’s instructions.
9
- Set the anti-skating control knob to the same value as
the stylus pressure.
10
- Install the dust cover to the main unit
