Audio Technica ATW-R3210 Скачать руководство пользователя

Страница: 8 / 32

Part names and functions

ATW-T3202

❶

Interchangeable microphone capsule

❷

Display

Shows the current status.
If no buttons are pressed for a period of 30 seconds, the display
will turn off.

❸

Grip case

❹

UP button

Use to select various settings.

❺

BACK button

Press to return to the previous screen.
Returns to the Main screen when pressed and held.

❻

IR sync window

Use to IR SYNC with the receiver (ATW-R3210).

❼

DOWN button

Use to select various settings.

❽

SET button

Press to confirm a selection.

❾

SYNC button

Use to IR SYNC with the receiver (ATW-R3210).

❿

Power switch

Use to turn the power on or off.

⓫

Battery cover

⓬

Function button

Press to turn the screen back on if it shuts off. Press and hold to
perform preselected function.

⓭

Indicator

LED that shows the status of the transmitter.

When the power is turned ON: Solid green
When the transmitter is muted: Solid red

⓮

Charging terminal

❸

❷

❶

❹ ❺ ❻

❼ ❽ ❾

❿

⓬

⓮

⓭

⓫

Содержание ATW-R3210

































Результаты поиска

Содержание ATW-R3210

Отзывы:

Похожие инструкции для ATW-R3210

Бренды по названию

Популярные бренды

Audio Technica ATW-R3210, Руководство пользователя

Результаты поиска

Содержание ATW-R3210

Отзывы:

Похожие инструкции для ATW-R3210

Бренды по названию

Популярные бренды