Audio Technica ATW-R3210 Скачать руководство пользователя

Страница: 7 / 32

Part names and functions

ATW-T3201

❶

Transmission antenna

❷

MUTE switch

Switches audio mute on and off.

❸

Indicator

LED that shows the status of the transmitter.

When the power is turned ON: Solid green
When the transmitter is muted: Solid red

❹

Function button

Press briefly to turn the screen back on if it shuts off. Press and
hold to perform preselected function.

❺

Input connector

Connect a microphone, a headworn microphone, a guitar cable, etc.

Pin 1: GND

Pin 4: +5 V output

Pin 2: Instrument input

Pin 3: Microphone input

❻

Display

Shows the current status.
If no buttons are pressed for a period of 30 seconds, the display
will turn off.

❼

SYNC button

Use to IR SYNC with the receiver (ATW-R3210).

❽

UP button

Use to select various settings.

❾

BACK button

Press to return to the previous screen.
Returns to the Main screen when pressed and held.

❿

Power switch

Use to turn the power on or off.

⓫

SET button

Press to confirm a selection.

⓬

DOWN button

Use to select various settings.

⓭

Battery cover

⓮

IR sync window

Use to IR SYNC with the receiver (ATW-R3210).

⓯

Charging terminal

❶

❷

❸

❹

❺

❻

❼

❽

❾

❿

⓫

⓭

⓬

⓮

⓯

❶

Содержание ATW-R3210

































Результаты поиска

Содержание ATW-R3210

Отзывы:

Похожие инструкции для ATW-R3210

Бренды по названию

Популярные бренды

Audio Technica ATW-R3210, Руководство пользователя

Результаты поиска

Содержание ATW-R3210

Отзывы:

Похожие инструкции для ATW-R3210

Бренды по названию

Популярные бренды