Audio Innovate AEM-100i Скачать руководство пользователя страница 12

Страница: 12 / 16

maintained and cleaned. It also already comes with the cut in points pre-adjusted for minimum dead

space. Please see

www.proxfade.co.uk

for more information on how to adjust and clean the crossfader.

Also check our website

www.audioinnovate.com

for information on accessories for cleaning and

adjusting the crossfader.

***VERY IMPORTANT: Because of the skill required to adjust and clean the crossfader, you shall

refer this operation to a qualified technician. The power cord must be unplugged before servicing or

damage to the unit may result. The faceplate and only the faceplate should be removed using a Phillips

screwdriver to access the crossfader. Knobs should all be removed by hand or very carefully lifted with

a screwdriver to avoid scratching and product damage. Please make sure that all parts are kept in a bin so

they are not misplaced prior to reassembly.

***SPECIAL NOTES FOR CLEANING THE CROSSFADER: In order to remove the crossfader

case for lubrication, you will first need to loosen the Phillips screw at the bottom of the crossfader.

Otherwise, you may damage the crossfader case when trying to remove it. In addition, please follow the

instructions for lubrication exactly or the fader will either be over-lubricated, causing fader noise, or

under-lubricated, causing the fader to wear more quickly.

Содержание AEM-100i
















