AUDAC LCR700 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 23

AUDAC LCR700 Скачать руководство пользователя страница 6

5

Safety Requirements

(Read the safety requirements before using the meter)

Warning:

Before taking any measurements, please isolate the DUT from the power supply.

You should remove the test leads from the meter before replacing the batteries in order to avoid an electric
shock. Make sure the circuit switch is disconnected before taking any measurements.

Do not use the meter if test leads look damaged. Please check regularly.

Caution:

When you can’t turn on the meter…

1. When you have turned off the meter a few seconds ago, it is perfectly normal. Please wait a moment to turn

it on again.

2. When you can’t operate the meter properly, please turn it off and restart later.

3. When the segments are fading away gradually, please wait 10 seconds to restart the meter.

4. When you can’t turn on the meter normally, please press the power key for 10 seconds and the meter will

restart.

«
...
4
5
6
7
8
...
»

Содержание LCR700
























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды